Guidebook for HACCP：HACCP-1.PDF

United States
Department of
Agriculture
Food Safety
and Inspection
Service
September 1999
HACCP-1
Guidebook for the
Preparation of
HACCP Plans
Additional copies of the Guidebook for the Preparation of
HACCP Plans and the Generic HACCP Models are available
from,
U.S,Department of Agriculture
Food Safety and Inspection Service (FSIS)
Office of Policy,Program Development,
and Evaluation (OPPDE)
Inspection Systems Development Division
Room 202,Cotton Annex Building
300 12
th
Street SW
Washington,D.C,20250-3700
Phone,(202) 720-3219
Fax,(202) 690-0824
This material is also available on the FSIS Homepage,
http://www.fsis.usda.gov/index.htm
United States Food Safety Washington,D.C,
Department of and Inspection 20250
Agriculture Service
September 8,1999
TO THE USERS OF THESE VOLUMES
As some of you may know,the Food Safety and Inspection Service (FSIS) received a substantial
package of comments on its Guidebook for Hazard Analysis and Critical Control Point (HACCP)
Plan Development and the 13 Generic HACCP models,from a coalition of industry and trade
associations,This package represents a large and thoughtful effort on the part of these
organizations,FSIS intends to give it the careful attention and response that it deserves,
The comments included many technical suggestions for improvements in the FSIS documents,It
also included reiteration of longstanding differing policy viewpoints that have been frequently
discussed by the Agency and the regulated industry,For the first time,the comments revealed
substantially differing expectations on the part of these organizations and FSIS with respect to
the purpose of the FSIS documents and their intended use,We want to address some aspects of
this latter point,
When the Pathogen Reduction/Hazard Analysis and Critical Control Point systems (PA/HACCP)
final regulation was published on July 25,1996,the DRAFT Guidebook was included as an
appendix,The Generic Models,developed for FSIS under contract,were available shortly
thereafter in April 1997,It was probably inevitable that there were significant differences
between the final regulatory language of CFR Part 417 and the DRAFT Generic Models as they
were developed independently,It would have been inappropriate for FSIS to discuss its final
regulatory language with any outside group,The contractor was appropriately proceeding from
what it knew best,the National Advisory Committee on Microbiological Criteria for Foods
(NACMCF) documents on the subject of HACCP,Therefore,FSIS accepted that work product
with full knowledge that significant revisions would be necessary,
As time passed,FSIS managers became increasingly uncomfortable with the situation in which
its major technical assistance documents did not appropriately and completely inform the
regulated industry of Agency expectations regarding regulatory compliance,Because the
intended audience for these technical assistance materials was primarily the very small
establishments,which the Agency believed to have the least HACCP-experience,the Agency
began the systematic revision of the documents to overcome this problem,We targeted the
summer of 1999 as the completion date for this effort,
FSIS now believes that others had very different ideas about the purpose and use of the
documents than it did,As is consistently reiterated in the documents themselves,they are not
designed to be used "as is." That is,they cannot be copied and used by an establishment to meet
all the regulatory requirements of 9 CFR Part 417,Nor were they designed to be the ultimate
teaching and training materials,as some would suggest,The development of ideal generic
models is left to others who may have an interest in doing so,The generic models are not
FSIS Form 2630-9 (6/86) EQUAL OPPORTUNITY IN EMPLOYMENT AND SERVICES
2
designed to extend or further interpret existing regulations; rather,they are designed to send the
user back to the regulations so he/she can become familiar with the requirements as well as the
flexibility they permit,The generic models are not designed to present new or alternative
methods of producing and processing meat and poultry products,That is also left to others with
an interest in doing so,
FSIS envisioned that the generic models might be used in the following way,Suppose a HACCP
team leader of a three-person HACCP team in a very small establishment attended a training
course,but the others on his/her team were not able to do so,Suppose the HACCP training
course met all the requirements of 417.7 but did not provide participants with much in the way of
"take away materials" like workbooks,practical questions and answers,access to follow-up
resources,etc.,which the Research Triangle Institute (RTI) needs assessment indicated were so
important to these establishments,The trained HACCP team leader returns to the establishment
and begins the process of attempting to develop HACCP plans for the company's products and
processes,He/she is quite confident that he/she has grasped the material presented in the training
course and begins to work with this team immediately,while the concepts are fresh in his/her
mind,
First,he/she has the rest of the team review the Canadian video and the Guidebook from FSIS so
that all members of his team have a basic level of information,
The team members begin their work,and as they proceed,some questions arise as to whether
what they have developed is appropriate,This is the point when FSIS expects the team to pick up
the appropriate generic model and get a sense of whether they are on the right track,They should
be able to determine whether the forms that they have developed,while different from the
various ones in the generic models and not the same as what other companies use,are acceptable
because they include the required information,They will also be able to discover what are some
typical food safety hazards that are reasonably likely to occur,as explicitly defined in 417.2,and
how to think through the problems that these hazards represent for their own products,They can
see how critical limits might arise from existing regulatory requirements like the ones for rapid
chilling of poultry products,They can also see that in the absence of settled regulatory
requirements,there may be several sources of scientific expertise,and they can choose to make a
conservative decision to provide a good margin of safety,They can find out the essential
differences between monitoring and verification and have a basis for making their choices about
verification activities and their frequencies,FSIS believes that these are useful,beneficial and
worthwhile functions for which its generic models can be used,
FSIS is publishing these updated revisions of the generic models,beginning with the Guidebook
and the Generic Model for Raw,Ground Product,because a large backlog of requests exists for
these two documents,FSIS intends to publish revisions of all the generic models no later than
September 30,1999,Moreover,as a result of public consultation,it may publish an additional
revision of some of these models,but given the backlog and the impending HACCP
implementation date,we considered it important to get a version of these documents out now,
We hope that these documents are helpful,
Guidebook
Table of Contents
Introduction………………………………………………………………………………,3
Developing a HACCP Plan..………………………………………………………….….,3
Policy Notices………………………………….…………………………………………,4
Preliminary Steps..………………………………………………………………………… 5
1,Assemble the HACCP team,including one person who is HACCP-trained…… 5
2,Describe the food and its method of production and distribution………………,6
3,Develop and verify process flow diagram(s)…………………………………….6
4,Decide whether products can be grouped using the process categories………… 7
PRINCIPLE I,CONDUCT A HAZARD ANALYSIS…………………..……………….,8
Biological Hazards………………………………………………………………… 8
Chemical Hazards…………………………………………………………………,8
Physical Hazards…………………………………………………………………..,9
PRINCIPLE II,IDENTIFY THE CRITICAL CONTROL POINTS.…………….………,10
PRINCIPLE III,ESTABLISH CRITICAL LIMITS FOR EACH CRITICAL
CONTROL POINT……….……………………………………………..,11
PRINCIPLE IV,ESTABLISH MONITORING PROCEDURES………………………...,12
PRINCIPLE V,ESTABLISH CORRECTIVE ACTIONS……………………………….,13
PRINCIPLE VI,ESTABLISH RECORDKEEPING PROCEDURES……………….…… 14
PRINCIPLE VII,ESTABLISH VERIFICATION PROCEDURES…………………….… 15
Validation………………………………………………………………………….,15
Ongoing verification……………………………………………………………….,15
Reassessment………………………………………………………………………,15
ATTACHMENTS
Attachment 1 – PRODUCT DESCRIPTION……………………………………… 17
Attachment 2 – PROCESS FLOW DIAGRAM (Raw product-ground)……………18
1
Guidebook
Attachment 3 – PROCESS FLOW DIAGRAM (Beef Slaughter)..….……………..19
Attachment 4 – Checklist of Questions (Hazard Analysis Process)………………..20
Attachment 5 – HAZARD IDENTIFICATION/ PREVENTIVE MEASURES..…,24
Attachment 6 – HAZARD ANALYSIS – RAW PRODUCT,GROUND………… 25
Attachment 7 – HACCP PLAN DEVELOPMENT FORM,MONITORING
PROCEDURES AND FREQUENCY……………..………….…,30
Attachment 8 – HACCP PLAN DEVELOPMENT FORM,CORRECTIVE
ACTIONS………………………………………………….……… 31
Attachment 9 – HACCP PLAN……………………………………………….…… 32
Attachment 10 – List of Some Typical Records of a HACCP System
in Operation……………………………………………..……… 33
APPENDIX A
PART 417 – HAZARD ANALYSIS AND CRITICAL CONTROL
POINT (HACCP) SYSTEMS……………………………….………,36
APPENDIX B
References for HACCP Teams…….……….……………………………………… 45
APPENDIX C
Livestock Carcasses and Poultry Carcasses Contaminated with Visible Fecal
Material……………………………………………………………………………,49
Contents of HACCP Plans,Critical Control Points..……………………………… 53
Contents of HACCP Plans…..…………………………………………………….,56
Establishment Review of Product Production Records……………………………,59
HACCP Plan Requirements and Meat and Poultry Product Processing
Categories; Policy Clarification…………………………………………………….62
Listeria Monocytogenes Contamination of Ready-to-Eat Products……………….,65
2
Guidebook
GUIDEBOOK FOR THE PREPARATION OF HACCP PLANS
Introduction
On July 25,1996,the Food Safety and Inspection Service (FSIS) of the United States Department
of Agriculture (USDA) published a final rule on Pathogen Reduction; Hazard Analysis and
Critical Control Point (HACCP) Systems (PR/HACCP),The PR/HACCP rule requires meat
and poultry plants under Federal inspection to take responsibility for,among other things,
reducing the contamination of meat and poultry products with disease-causing (pathogenic)
bacteria,Reducing contamination with pathogenic bacteria is a key factor in reducing the number
of deaths and illnesses linked to meat and poultry products,The Preamble to the final rule
describes an overall system in which preventive and corrective measures are instituted at each
stage of the food production process where food safety hazards could occur,
The HACCP requirements that plants must meet are set out in 9 CFR Part 417,HACCP is a
scientific system for process control that has long been used in food production to prevent
problems by applying controls at points in a food production process where hazards could be
controlled,reduced or eliminated,A plant must have an effective HACCP system to comply with
regulatory requirements and prevent adulteration of product,
The HACCP regulatory requirements become effective on different dates for plants of differing
sizes,
Large plants – those with 500 or more employees – on January 26,1998;
Smaller plants – those with fewer than 500 but at least 10 employees on January 25,1999; and
Very small plants – those with fewer than 10 employees or annual sales less than $2.5 million –
on January 25,2000,
Note,This Guidebook and other FSIS technical assistance materials are designed to assist
establishments subject to the regulatory requirements of 9 CFR Part 417 in complying with those
requirements,Part 417 is reproduced in Appendix A,These regulatory requirements are slightly
different from the various explanations of HACCP developed by the National Advisory
Committee on Microbiological Criteria for Foods (NACMCF),the most recent version of which
was published in 1997,
Developing a HACCP Plan
FSIS is providing this Guidebook for the Preparation of HACCP Plans to help plants develop
and set up their HACCP systems,There are other FSIS publications,which may be helpful,This
Guidebook is the most basic of the FSIS materials,FSIS has also developed thirteen generic
models that plants can use to see if their specific plans are generally on target or help them get
started,The generic models are more specific than this Guidebook and each one has at least one
fully developed product example which establishment HACCP teams can study,However,even
3
Guidebook
though the generic models have more detailed information,they are not designed to be used,as
is.” A company will still need to tailor the plan to suit the specific circumstances of its own
production process,
Policy Notices
In order to clarify issues,which were raised in conjunction with the first implementation date,
FSIS published a series of Policy Notices in the Federal Register,Copies are included as
Appendix C,The issues addressed include,
Livestock Carcasses and Poultry Carcasses Contaminated with Visible Fecal
Material (November 28,1997)
Contents of HACCP Plans; Critical Control Points (January 30,1998)
Contents of HACCP Plans (January 30,1998)
Establishment Review of Product Production Records (March 6,1998)
HACCP Plan Requirements and Meat and Poultry Product Processing Categories;
Policy Clarification (April 1,1998)
Listeria Monocytogenes Contamination of Ready-to-Eat Products (May 26,1999)
Establishments may wish to refer to these Policy Notices if they need further clarification about
the aspects of the regulations that are addressed,
In addition to written materials,FSIS has held a number of events to assist establishments in
meeting regulatory requirements in a timely manner; these include both implementation
conferences and technical assistance workshops,
Finally,FSIS has developed and put in place resources which are available to answer specific
questions; the FSIS Technical Service Center operates a HACCP Helpline (1-800-233-3935 ext.2)
which provides answers to technical questions from inspection personnel and establishments,
Also FSIS has organized HACCP contacts in each of the states,to which establishments can turn
for help with their specific problems,The District Office can provide information on the State
HACCP Network,
Advice and assistance on developing HACCP systems can be obtained from many sources other
than FSIS (use the Internet web site,www.nal.usda.gov/fnic/foodborne/haccp/index.shtml),
FSIS encourages establishment officials to consult and use a variety of resources as they go about
planning,documenting,and validating their HACCP systems,Also included in this Guidebook
is a list of references that can be used by all HACCP teams that have been included as Appendix
B,However,when HACCP regulations become effective in an establishment,it is the
requirements of Part 417 that must be met,Establishment employees with a thorough
understanding of HACCP concepts should still review the regulatory requirements of this part to
4
Guidebook
make sure they achieve compliance,This Guidebook has been revised to make it easier for users
to relate its practical advice with the need to be in compliance with regulatory requirements,
Preliminary Steps
FSIS and most HACCP experts believe that a company will do a better job of HACCP plan
development if it takes some preliminary steps before it attempts to apply the seven principles
and write a plan,FSIS believes that a company should take the following steps to get started,
1. Assemble the HACCP team,including one person (consultant,employee,or other
resource) who is HACCP-trained,
2. Describe the food and its method of production and distribution; identify the intended
use and consumers of the products,
3,Develop and verify process flow diagram(s),
4,Decide whether products can be grouped using the process categories in 417.2(b)(1),
The first part of this Guidebook discusses how companies,especially small or very small
companies,can go about taking these preliminary steps,Numbers 2-4 are parts of the regulatory
requirements in §417.2(a),
1,Assemble the HACCP team,including one person who is HACCP-trained,
Assembling a HACCP team may seem like a daunting task,especially for the owner of a very
small or family-centered company,However,FSIS strongly encourages companies to have more
than one person working on the development of HACCP system(s),This is because HACCP
system development is one of those tasks that are probably better done by more than one person,
even in a very small company,HACCP is an overall process control system and we believe it
takes a variety of different kinds of knowledge and experience to develop a good system,If your
company has only a few people in it,they may all need to be on the HACCP team,because they
all probably have multiple roles and responsibilities in the company’s operations,
You should consider including on your HACCP team,some resources which may be outside your
company,You may be able to get help from a trade association or from a local college,university
or extension office which has people in it who know about HACCP process control systems,It is
possible that companies which supply or receive your products and have already implemented
HACCP may be interested in and willing to provide assistance,FSIS has offered technical
assistance workshops to groups of plants that came together to a central location and worked
through the process of system development in small steps,
One resource you must include is an individual who has been trained in HACCP in accordance
with the requirements of Sec,417.7,These requirements are that the individual has successfully
completed a course in applying the seven principles of HACCP to meat or poultry product
processing; the course needs to have included a segment on HACCP plan development for a
specific product and a segment on record review,This HACCP-trained individual does not
5
Guidebook
need to be a company employee,but does need to be available to you for plan development and
for certain other functions,like reassessing your HACCP plan(s),
2. Describe the food and its method of production and distribution; identify the
intended use and consumers of the products,
The next preliminary step to take is to have the HACCP team describe the product(s) and their
methods of production and distribution,If your team includes the people who know how things
work in your operations,they should be able to do this quite easily,The important thing for them
to keep in mind is that they need to include every step in the process,In order to help you make
sure you include all the key information,we have prepared a form which could be used to
accomplish this task,Attachment 1 is this form and like all the forms in this Guidebook,its use
is optional,
Whether you use the form or not,the following questions should be answered when you describe
the product,
1,What is the common name of the product?
2,How is the product to be used?
3,What type of packaging encloses the product?
4,What is the length of shelf life of the product,at what temperature?
5. Where will the product be sold? *Who is the intended consumer and what is the intended
use?
6,What labeling instructions are needed?
7,Is special distribution control needed?
* Regulatory requirement
After your team has described the products in words,they can move on to the next preliminary
step,
3,Develop and verify process flow diagram(s),
A flow diagram is a simple schematic picture of the process you use in your plant to produce the
product,You do not need any fancy equipment,such as a computer,to produce a flow diagram,
However,it does need to be an accurate,clear sketch of the process used in your plant to make the
product,Attachment 2 is an example of a simple flow diagram for a relatively simple process;
Attachment 3 is a more complex flow diagram for a more complicated process,Either one
would be an adequate flow diagram if it accurately pictured what was actually happening in the
plant,
The best means to make sure your flow diagram is accurate is to have the HACCP team verify it
by walking through the plant and making sure all the steps in the process you carry out are
included in the flow diagram,Verifying the flow diagram is a step your team should be sure to do
carefully,It is also a common means by which auditors or inspectors verify that a particular flow
diagram is correct and complete,
6
Guidebook
When you are certain that you have an accurate flow diagram and your team has verified it,it is
time to move to the final preliminary step,
4,Decide whether products can be grouped using the process categories in 417.2(b)(1),
This part of the regulations lists nine process categories into which meat and poultry production
can be grouped; they and some examples are,
(i) Slaughter--all species,beef,swine,and poultry
(ii) Raw product—ground,ground beef,ground pork,ground turkey
(iii) Raw product--not ground,boneless cuts,steaks
(iv) Thermally processed--commercially sterile,canned beef stew,Pasta with meat
(v) Not heat treated--shelf stable,summer sausage,dry salami
(vi) Heat treated--shelf stable,meat and poultry jerky,snack sticks
(vii) Fully cooked--not shelf stable,hot dogs,wieners,roast beef,ham
(viii) Heat treated but not fully cooked--not shelf stable,partially cooked patties,bacon
(ix) Product with secondary inhibitors--not shelf stable,corned beef,cured beef
tongue
One way to cut down on the paperwork that is a part of HACCP system is to control all products
in the same process category using a single HACCP plan,This is especially advantageous for
very small establishments which may produce many different products,If those products differ
only in characteristics that would not affect safety,e.g,the amount or kind of seasoning used (hot
vs,mild),they are clearly in the same process category and may be covered by the same HACCP
plan,
FSIS has developed eleven generic HACCP models for the processes listed above and two more
specific processes,Mechanically Separated (Species)/ Mechanically Deboned Poultry and
Irradiation (including all forms of approved irradiation procedures),
Now you have completed the preliminary steps that will prepare you for HACCP system
development,It is time for your team to apply the seven principles of HACCP and develop your
HACCP plan,The next seven sections (principles) of this Guidebook will take you through this
process,
7
Guidebook
PRINCIPLE I,CONDUCT A HAZARD ANALYSIS
The first principle of HACCP is to conduct a hazard analysis,Part 417 contains definitions as
well as specific provisions which affect how your HACCP team must go about conducting its
hazard analysis,Before beginning the process,your team should review the definitions of food
safety hazard and preventive measure,and look specifically at the requirements of 417.2(a),
A. Conducting a hazard analysis is generally considered to be a two-step process,The first step
is to identify the threats to human health,which might be introduced into meat and poultry
products as those products are produced,These hazards are usually grouped into three
categories,Biological (including microbiological),Chemical,and Physical,
1,Biological Hazards
Biological hazards are living organisms that can make food unsafe to eat,Biological hazards
may be bacterial,parasitical,or viral,Biological hazards are frequently associated with the raw
materials from which meat and poultry products are made,including the animals and birds,
which are primary components,However,biological hazards may be introduced during the
processing of meat and poultry products,from the people who are involved in the processing;
from the environment in which the foods are processed; from other ingredients in the products;
or from the processes themselves,
Identifying the biological hazards to which your production processes might be subjected is
clearly a difficult and important task—one that requires all the expertise that your HACCP team
can bring to it,Currently,there is a great deal of emphasis on microbial hazards associated with
meat and poultry products,Some of the major pathogens that may be associated with meat and
poultry products are,Salmonella,Campylobacter jejuni,Escherichia coli 0157:H7,Listeria
monocytogenes,Clostridium botulinum,Staphylococcus aureus,and Yersinia enterocolitica,
For details,refer to NACMCF document reference 14 listed in Appendix B,
2,Chemical Hazards
Chemical hazards may be the result of something naturally occurring in foods or added during
the processing of foods,Harmful chemicals have been associated with both acute cases of
foodborne illness and chronic illness,
Naturally occurring chemical hazards are those that are natural constituents of foods and not the
result of environmental,industrial,or other contamination,They include aflatoxins,mycotoxins
and shellfish toxins,
Added chemical hazards are those which are intentionally or sometimes unintentionally added to
food during the growing,harvesting,storage,processing,packaging,or distribution phases of
production,This group of chemical hazards is very broad and might include components of
animal feed or drinking water,animal drugs,pesticides,food ingredients themselves,or
chemicals used in the processing establishment such as lubricants,cleaners,paints,and coatings,
8
Guidebook
3,Physical Hazards
A physical hazard is a physical component of a food that is unexpected and may cause illness or
injury to the person consuming the food,Foreign materials such as glass,metal,or plastic are
familiar physical hazards in meat and poultry products,usually found because a process or a
piece of equipment has not been properly controlled while the food was being produced,
There are a number of situations that can contribute to physical hazards in foods; they include,
--Contaminated raw materials;
--Poorly designed or poorly maintained facilities and equipment;
--Contaminated packaging materials; and,
--Inattention to details by employees with key responsibilities,
B. This first step in identifying hazards which might be associated with your production process
might be considered like a,brainstorming” session,Your HACCP team should use the flow
diagram and product description,which you created in your preliminary steps,and
systematically think about what could occur at each step in the process,Attachment 4 is a
checklist of questions which might help your team to be as thorough as possible in
considering the hazards which might be associated with your process,
C. The second step in performing a hazard analysis is to identify preventive measures that could
be used to control each hazard,Preventive measures are the physical,chemical,or other
means that can be used to control a food safety hazard,Attachment 5 is a form which you
can use to go through your process systematically,identify the hazards which might occur at
each step in the process and the preventive measures which might be used to prevent,
eliminate,or reduce each hazard to an acceptable level which you can use in conjunction
with the checklist,More than one preventive measure may be needed to control a food safety
hazard and more than one food safety hazard may be controlled by a specific preventive
measure,
D. Attachment 6 is a hazard analysis,which has been completed for a simple raw,ground
process,When developing your hazard analysis,be sure to remember that supporting
documentation for the decisions reached by the team is very important and a regulatory
requirement [§ 417.5(a)(1)],The supporting documentation can consist of the regulatory
citation if the critical limit is based on a regulation,a scientific paper,study,or in-plant
study,Historical information about the process can also be used,This information should be
summarized as part of the supporting documentation for the team’s decisions,When making
determinations about whether a hazard is reasonably likely to occur,it is helpful to list the
actual hazard or organism of concern,For example,metal contamination from equipment,
Salmonella,Escherichia coli O157:H7,Campylobacter jejuni,Listeria monocytogenes or
other specific pathogenic hazards,or a specific residue that is known to occur in a like
product,You will find this information very helpful when yearly reassessment,a deviation,
or an unforeseen hazard occurs,
9
Guidebook
We cannot overemphasize how important it is to do a good job on your hazard analysis,This is
often a difficult and time-consuming step,and one that requires all the various technical and
scientific resources you can obtain,You can refer to the NACMCF DRAFT document -,FSIS
Microbiological Hazard Identification Guide for Meat and Poultry Components of Products
Produced by Very Small Plants”,August 1999 (Appendix B,Reference 14)”,We know that
doing a good job and taking your time here is worth the effort,You cannot expect to develop a
good HACCP system if you have not been careful and thorough in your hazard analysis,
PRINCIPLE II,IDENTIFY THE CRITICAL CONTROL POINTS
The second HACCP principle is to identify the critical control points (CCPs) in the process,A
CCP is a point,step,or procedure in a food process at which control can be applied and,as a
result,a food safety hazard can be prevented,eliminated,or reduced to acceptable levels,
So far,in developing the HACCP plan,your HACCP team has identified biological,chemical,
and physical hazards in the raw materials and the ingredients you use as well as in the steps of
your process,For each food safety hazard reasonably likely to occur,you have identified a
preventive measure,Your next step is to find the point or points in the process where these
preventive measures should be applied,
Fortunately,a great deal of work has already been done in identifying points where control can
be applied in a process, Many points are commonly recognized in various food processing and
production systems,Some common points where control can be applied in your process include,
--Chilling to temperatures that minimize microbial growth;
--Cooking to specific temperatures for exact times in order to destroy microbial
pathogens;
--Product formulations,such as the addition of cultures or adjustment of pH or water
activity;
--Processing procedures such as filling and sealing cans; and,
--Slaughter procedures such as evisceration or antimicrobial interventions,
These are just a few examples of measures that may be CCPs,There are many more
possibilities,Different facilities preparing the same food can differ in the number and types of
CCPs they choose to use,This is to be expected,
The FSIS generic models,as well as other generic models,give you some ideas about what CCPs
might work in the various process categories which are discussed,Your team needs to remember
that these are just ideas designed to help get your team thinking creatively and carefully about
your own processes and how you want to control them with your HACCP system,
Note,Identifying CCPs is one area in which there are differences between the regulatory
requirements of Part 417 and the NACMCF guidance materials (reference 13),The latter
include the use of a Decision Tree; the Decision Tree approach is not necessary for you to meet
regulatory requirements; however,the thought process may be helpful,You must make sure that
your HACCP system meets regulatory requirements,
10
Guidebook
PRINCIPLE III,ESTABLISH CRITICAL LIMITS FOR EACH CRITICAL CONTROL
POINT
HACCP principle three instructs your team to establish critical limits for each preventive
measure you will carry out at each CCP,This step involves establishing a criterion that must be
met for each preventive measure associated with a CCP,Part 417 defines a critical limit as,the
maximum or minimum value to which a physical,biological,or chemical hazard must be
controlled at a critical control point to prevent,eliminate,or reduce to an acceptable level the
occurrence of the identified food safety hazard,
Critical limits are the boundaries of safety for preventive measures put in place at CCPs,A
critical limit will usually be a reading or observation such as a temperature,a time,a product
property such as water activity,or a chemical property such as available chlorine,salt
concentration,or pH,Critical limits need to be exact and specific; HACCP plans should not
include ranges as critical limits,
Many critical limits for identified CCPs have been established,either through regulatory
requirements or through the technical and scientific literature,which are the bases of production
processes,Your HACCP team will probably be familiar with many of these established critical
limits such as,the minimum internal temperature to which products must be cooked; the time
which may elapse while product is being cooled to a specific temperature; the maximum
dimensions of any metal fragments which could be found in products,These critical limits must
be met if product safety is to be maintained,
When deciding what your critical limits should be,there are several sources to consider,First
are the regulatory requirements,which apply to your processes,These must be met,For
example,if you produce cooked beef products,you must have critical limits that meet the current
FSIS regulatory requirements for those products,There may be other sources of critical limits,
such as the times and temperatures that you use in making the products you produce,These may
be based on scientific and technical information from studies or food processing textbooks or
they may be based on family recipes that have been passed down from one generation to the next
and have scientifically been shown to produce safe product,Critical limits may be drawn from
specific challenge studies or from recognized experts,In any case,you need to establish a
critical limit for each preventive measure you intend to apply at your CCPs,
There are two types of critical limits,A critical limit can be an upper limit where a set amount or
level cannot be exceeded,A critical limit can also be a lower limit where a minimum amount is
required to produce the safe effect,To address the hazard in ground product of metal fragments
from the grinding equipment,the upper critical limit for the preventive measure could be no
sharp metal fragments more than 1/32 inch,A grinding room temperature of 50° F to help
control pathogen growth is another kind of upper critical limit,An example of a lower critical
limit would be the addition of an acidifier to inhibit bacterial growth,
11
Guidebook
PRINCIPLE IV,ESTABLISH MONITORING PROCEDURES
To carry out HACCP principle four,your team needs to establish monitoring procedures,
Monitoring procedures are those things,which are done routinely,either by employee or by
mechanical means,which,measure the process at a given CCP,and create a record for future
use,Some monitoring procedures are employee observations or checks,such as checking the
documentation accompanying incoming materials,Some monitoring procedures are records
from instruments,such as recording thermometers,
Continuous monitoring is always preferred when it is feasible,When it is not possible,then your
HACCP team will need to decide what will be their non-continuous monitoring procedures and
how frequently they will be performed,There are several issues to consider when deciding the
frequency of non-continuous monitoring checks; the most important is that the procedures must
be performed sufficiently often to accurately reflect that the process is under control,Expert
advice from people with knowledge of practical statistics and statistical process control will be
important in making your decisions about frequency,
Another factor that HACCP teams must consider is the capacity of the plant to take corrective
actions when monitoring procedures reveal that there have been deviations from critical limits,
When monitoring procedures show that there has been a deviation from a critical limit,
corrective actions need to be applied to all the potentially noncomplying product,This usually
includes all the product produced since the time of the last successful monitoring procedure
result,So,if your monitoring procedure was to perform a physical check on arriving product,
and your team decided to do this only once per shift,a deviation from the critical limit would
mean that you needed to apply corrective actions to all the product which had arrived during the
shift,
Another matter for your HACCP team to consider when they are deciding on what should be the
monitoring procedures and how frequently they should be performed is the need for rapid,real
time feedback,Generally,physical and chemical procedures are preferred over microbial
approaches for monitoring because they provide more rapid feedback,
Monitoring procedures need to be well planned and effective because of the potentially serious
consequences of loss of control,Employees monitoring CCPs should be trained in the technique
to be used to monitor each preventive measure or control,They should fully understand the
purpose and importance of monitoring and accurately report monitoring activities and results,
They must have complete access to the CCP being monitored and to the process-monitoring
instruments being used,
The persons performing monitoring must record exact values where exact values are indicated,
not,yes/no” or,OK” observations,This means that if the critical limit is a minimum internal
temperature of 160° F,the observations on the monitoring record would be recorded as,162 °F,”
“163°F” rather than,yes” or,OK.”
Attachment 7 is a simple form,which your team might use to help them decide on monitoring
procedures and their frequency,
12
Guidebook
PRINCIPLE V,ESTABLISH CORRECTIVE ACTIONS
HACCP principle five says,Establish corrective actions to be taken when monitoring shows that
there is a deviation from a critical limit,In addition,§ 417.3 identifies the four features of
corrective actions that FSIS regulators will be checking; they are,
1,Has the cause of the deviation been identified and eliminated?;
2,Will the CCP be under control after the corrective action has been taken?;
3,Have measures to prevent recurrence of the deviation been established?; and,
4,Do the corrective action procedures make sure that no product,which is injurious to
health or otherwise adulterated because of the deviation enters commerce?
HACCP is a preventive system to correct problems before they affect the safety of the food
products people actually consume,Deviations from critical limits will occur; therefore,you need
to have a plan to make sure those deviations do not lead to unsafe products,Planned corrective
actions are the way you do this,Your HACCP team needs to understand how important it is to
carefully carry out this principle,
For each CCP,your team needs to devise a standardized set of actions that company employees
will follow when there is a deviation from a critical limit,These are some questions they might
ask in developing corrective actions,
How will people be informed when the deviation occurs? If a person is performing the
monitoring procedure,who will that person contact?
Who will be responsible for controlling the product that may have been affected by the
deviation? How should that person decide how much product needs to be controlled?
Who will be involved in deciding what to do about the product which might have been
affected by the deviation?
How will we decide what was the cause of the deviation? If we need technical experts
outside the company,how do we get them?
Once we have figured out what was the cause of the deviation,who will be involved in
deciding how to get the process back in control and prevent recurrence of the deviation?
If our HACCP trained individual is not available in the plant immediately,how can we
get HACCP expertise to help decide if our plan needs to be modified?
Who in the company needs to sign off on any modifications to our plan?
Who will be responsible for keeping the records of everything we do in response to a
deviation from a critical limit at this CCP?
13
Guidebook
If any person who has a responsibility in our corrective action plan is not available,who
will be the back-up?
Is this set of corrective actions feasible at all times?
Attachment 8 is a simple form to help your HACCP team make sure they have developed
appropriate corrective actions for each CCP,Part 417 includes regulatory requirements,which
must be followed when a deviation not covered by a specific corrective action occurs or if an
unforeseen hazard occurs,Your team should study § 417.3(b) so that you know what to do when
this happens,In many ways,the actions to be taken will be generally similar to what you plan to
do at any specific CCP—get control of the product,figure out what was the cause and how to
keep it from happening again,decide whether to modify your HACCP plan,etc,Your team
should at least think about how you want to handle these situations,
PRINCIPLE VI,ESTABLISH RECORDKEEPING PROCEDURES
HACCP principle number 6 is to establish effective recordkeeping procedures that document the
HACCP system,The regulatory recordkeeping requirements for meat and poultry
establishments are found in § 417.5 and are quite comprehensive,Your team should review
them carefully,
Even though people often complain about it,recordkeeping is an essential feature of a HACCP
system and must be planned and carried out as carefully as any other element,This principle
requires the development and maintenance of records about both plan development and the
operation of the system,In a study on HACCP prepared by the Department of Commerce it was
clear that,without recordkeeping,problems were more likely to recur,
Even though people may grumble about keeping records,the practice can be made sensible and
suitable for the operation in question,Clearly more sophisticated records will be required for
more complex operations,One way to approach development of the recordkeeping requirements
of your HACCP system is to review the records you already keep and see if they are suitable,in
their present form or with minor modifications,to serve the purposes of your HACCP system,
The best recordkeeping system is usually the simplest one that can be easily integrated into the
existing operation,
When you are setting up your recordkeeping system,think about who will be in the best position
to make the record entry,who will need to review the record prior to shipping,plus,when and
where will be the best place to keep the records,Think about making simple understandable
forms that will work well in your situation,Make sure your employees know exactly what is
expected if they are responsible for making a record entry,It is extremely important that they
sign and date the records at the time the specific event occurs,
Records do not need to be in any particular format,Often HACCP plans are presented in a
tabular form,Attachment 9 is an example of a blank HACCP Plan form in a typical format,
Attachment 10 is a list of some typical records of a HACCP system in operation,The
14
Guidebook
PR/HACCP regulation also includes a requirement for preshipment review in § 417.5(c),This
step can provide you added assurance that you have done everything in your HACCP plan before
you ship the product,There are examples in each of the generic models on how this can be
accomplished,
PRINCIPLE VII,ESTABLISH VERIFICATION PROCEDURES
HACCP principle seven is to establish verification procedures to make sure the plan is working
correctly,
Your team needs to decide on what procedures the plant will perform to verify that the HACCP
system is working effectively and how often these actions will be performed,Verification uses
methods,procedures,or tests in addition to those used in monitoring to see whether the HACCP
system is in compliance with the HACCP plan or whether the HACCP plan needs modification,
There are three types of verification,
Validation is the initial phase in which the plan is tested and reviewed,The choices made while
working through the preliminary steps and HACCP principles must be repeatedly tested and
shown to prevent or control identified hazards in the,real world”,In this phase,microbial or
residue testing can be used effectively to verify that the process is in control and is producing
acceptable product,Such testing provides clear evidence that the techniques and methods
adopted by the plant to control hazards are not just effective in theory but will work in this
specific plant,
Ongoing verification ensures that the HACCP plan is working effectively on a day-to-day basis,
This type of verification includes such tasks as calibrating monitoring instruments,observing
monitoring activities and corrective actions,and reviewing HACCP records to see that they are
being made and kept according to the plan,
Reassessment is an overall review of the plan that must be performed at least annually,or
whenever any changes occur that could affect the hazard analysis or alter the HACCP plan,
Reassessment is similar to validation in that it considers whether the plan is adequate in general
rather than focusing on the plan's daily operations,It is also similar to validation in that it must
be done by a HACCP-trained person,
15
Guidebook
ATTACHMENTS
16
Guidebook
PRODUCT DESCRIPTION Attachment 1
PROCESS CATEGORY,SLAUGHTER
PRODUCT,BEEF
1,COMMON NAME? BEEF; BEEF VARIETY MEATS
2,HOW IS IT TO BE USED? CARCASSES; VARIETY MEATS
3,TYPE OF PACKAGE? CARCASSES – NONE; VARIETY
MEATS – 50 POUND BOXES
4,LENGTH OF SHELF LIFE,
AT WHAT TEMPERATURE? 7 DAYS AT 40° F
5,WHERE WILL IT BE SOLD? WHOLESALE TO DISTRIBUTORS
CONSUMERS? ONLY
INTENDED USE?
6,LABELING INSTRUCTIONS? KEEP REFRIGERATED
7,IS SPECIAL DISTRIBUTION KEEP REFRIGERATED
CONTROL NEEDED?
17
Guidebook
PROCESS FLOW DIAGRAM Attachment 2
PROCESS CATEGORY,RAW PRODUCT,GROUND
PRODUCT,FRESH PORK SAUSAGE
________________________________________________________________
RECEIVING
PACKAGING
MATERIALS
RECEIVING
NONMEAT
INGREDIENTS
STORAGE
PACKAGING
MATERIALS
STORAGE
NONMEAT
INGREDIENTS
ASSEMBLE/
PREWEIGH
NONMEAT
INGREDIENTS
GRIND/BLEND ASSEMBLE/
WEIGH MEAT
STORAGE
MEAT (COLD)
RECEIVING
MEAT
SAUSAGE
STUFFER REWORK
PACKAGING/
LABELING
FINISHED
PRODUCT
STORAGE
(COLD)
SHIPPING
18
Guidebook
PROCESS FLOW DIAGRAM Attachment 3
PROCESS CATEGORY,SLAUGHTER
PRODUCT,BEEF
RECEIVING
PACKAGING
MATERIALS
RECEIVING LIVE CATTLE
STUNNING/BLEEDING
HEAD/SHANK
REMOVAL
SKINNING
EVISCERATION
SPLITTING
TRIM RAIL
FINAL WASH
VISCERA
PROCESSING
VARIETY
MEATS
PRODUCTION
CHILLING
PACKAGING/LABELING
FINISHED PRODUCT
STORAGE (COLD)
SHIPPING
STORAGE
PACKAGING
MATERIALS
19
Guidebook
Checklist of Questions Attachment 4
(Hazard Analysis Process)
This point in hazard analysis consists of asking a series of questions that are
appropriate to each step in the flow diagram,The hazard analysis should question the
effect of a variety of factors on the safety of the food,
1,Ingredients
Does the food contain any sensitive ingredients that are likely to present
microbiological hazards (e.g,Salmonella,Staphylococcus aureus),chemical
hazards (e.g.,aflatoxin,antibiotic,or pesticide residues) or physical hazards
(stones,glass,bone,metal)?
2,Intrinsic factors of food
Physical characteristics and composition (e.g.,pH,type of acids,fermentable
carbohydrates,water activity,preservatives) of the food during and after
preparation which can cause or prevent a hazard,
Which intrinsic factors of the food must be controlled in order to ensure food
safety?
Does the food permit survival or multiplication of pathogens and/or toxin
formation before or during preparation?
Will the food permit survival or multiplication of pathogens and/or toxin
formation during subsequent steps of preparation,storage,or consumer
possession?
Are there other similar products in the market place? What has been the safety
record for these products?
3,Procedures used for preparation/processing
Does the preparation procedure or process include a controllable step that
destroys pathogens or their toxins? Consider both vegetative cells and spores,
Is the product subject to recontamination between the preparation step (e.g.,
cooking) and packaging?
4,Microbial content of the food
Is the food commercially sterile (i.e.,low acid canned food)?
20
Guidebook
Is it likely that the food will contain viable sporeforming or nonsporeforming
pathogens?
What is the normal microbial content of the food stored under proper conditions?
Does the microbial population change during the time the food is stored before
consumption?
Does that change in microbial population alter the safety of the food?
5,Facility design
Does the layout of the facility provide an adequate separation of raw materials
from ready-to-eat foods?
Is positive air pressure maintained in product packaging areas? Is this essential
for product safety?
Is the traffic pattern for people and moving equipment a potential source of
contamination?
6,Equipment design
Will the equipment provide the time/temperature control that is necessary to meet
critical limits?
Is the equipment properly sized for the volume of food that will be prepared?
Can the equipment be controlled so that the variation in performance will be
within the tolerances required to produce a safe food?
Is the equipment reliable or is it prone to frequent breakdowns?
Is the equipment designed so that it can be cleaned and sanitized?
Is product contamination with hazardous substances,e.g.,glass,likely to occur?
What product safety devices such as time/temperature integrators are used to
enhance consumer safety?
7,Packaging
Does the method of packaging affect the multiplication of microbial pathogens
and/or the formation of toxins?
21
Guidebook
Is the packaging material resistant to damage,thereby preventing the entrance of
microbial contamination?
Is the package clearly labeled,Keep Refrigerated” if this is required for safety?
Does the package include instructions for the safe handling and preparation of the
food by the consumer?
Are tamper-evident packaging features used?
Is each package legibly and accurately coded to indicate production lot?
Does each package contain the proper label?
8,Sanitation
Can the sanitation practices that are employed impact upon the safety of the food
that is being prepared?
Can the facility be cleaned and sanitized to permit the safe handling of foods?
Is it possible to provide sanitary conditions consistently and adequately to ensure
safe foods?
9,Employee health,hygiene,and education
Can employee health or personal hygiene practices impact the safety of the food
being prepared?
Do the employees understand the food preparation process and the factors they
must control to ensure safe foods?
Will the employees inform management of a problem,which could impact food
safety?
10,Conditions of storage between packaging and the consumer
What is the likelihood that the food will be improperly stored at the wrong
temperature?
Would storage at improper temperature lead to a microbiologically unsafe food?
22
Guidebook
11,Intended use
Will the food be heated by the consumer?
Will there likely be leftovers?
12,Intended consumer
Is the food intended for the general public,i.e.,a population that does not have an
increased risk of becoming ill?
Is the food intended for consumption by a population with increased susceptibility
to illness (e.g.,infants,the elderly,the infirm,and immuno compromised
individuals)?
23
Guidebook
Attachment 5
HAZARD IDENTIFICATION/PREVENTIVE MEASURES
PROCESS CATEGORY,
PRODUCT,
PROCESS STEP
FOOD SAFETY HAZARD PREVENTIVE MEASURE(S)
APPROVED BY:_________________________________________ Date:____________
24
Guidebook
HAZARD ANALYSIS – RAW PRODUCT,GROUND – Fresh Pork Sausage
Attachment 6
Process Step
Food Safety Hazard
Reasonably
Likely to
Occur?
Basis If Yes in Column 3,
What Measures Could
be Applied to Prevent,
Eliminate,or Reduce
the Hazard to an
Acceptable Level?
Critical Control
Point
Receiving - Meat Biological,Pathogens -
microbial (Salmonella,
Escherichia coli
0157:H7)
Yes Either pathogen may be
present on incoming raw
product,
Letters of guaranty that
supplier meets base line
criteria or in process
control of room
temperature or storage
temperature to prevent
growth
1B
Chemical – None
Physical – Foreign
materials
No Plant records show that
there has been no
incidence of foreign
materials in products
received into the plant,
Receiving – Nonmeat
Ingredients/Packaging
Materials
Biological – None
Chemical – Not
acceptable for
intended use
No Letters of guaranty are
received from all
suppliers of nonmeat
ingredients and
packaging materials,
Physical – Foreign
materials
No Plant records
demonstrate that foreign
material contamination
has not occurred during
the past several years,
25
Guidebook
HAZARD ANALYSIS – RAW PRODUCT,GROUND
Attachment 6
Process Step Food Safety
Hazard
Reasonably
Likely to
Occur?
Basis If Yes in Column 3,
What Measures Could
be Applied to Prevent,
Eliminate,or Reduce
the Hazard to an
Acceptable Level?
Critical Control
Point
Storage (Cold) - Meat Biological – Pathogens
(List those specific to
the product)
Yes Pathogens are
reasonably likely to
grow in this product if
temperature is not
maintained at or below
a level sufficient to
preclude the growth,
Maintain product
temperature at or below a
level sufficient to preclude
pathogen growth,
2B
Chemical – None
Physical – None
Storage – Nonmeat
Ingredients/Packaging
Materials
Biological – None
Chemical – None
Physical – None
Assemble/Pre-weigh
Nonmeat Ingredients
Biological – None
Chemical- None
Physical – None
Assemble/Weigh Meat Biological – None
Chemical – None
Physical – None
26
Guidebook
HAZARD ANALYSIS – RAW PRODUCT,GROUND
Attachment 6
Process Step Food Safety
Hazard
Reasonably
Likely to
Occur?
Basis If Yes in Column 3,
What Measures Could
be Applied to Prevent,
Eliminate,or Reduce
the Hazard to an
Acceptable Level?
Critical Control
Point
Grind/Blend Biological - None
Chemical – None
Physical – Metal
contamination
Yes Plant records show that
during the grinding
process metal
contamination is likely
to occur,
In-line magnets are installed
on the stuffing lines,
3P
Sausage Stuffer Biological – None
Chemical – None
Physical – None
Rework Biological – Pathogens Yes Rework can be a source
of continuing
inoculation with
pathogens,
Rework is condemned or
used in a cooked product at
the plant,If it will not be
used that day or is coded
and not mixed so that the
identity and total time in
plant or process can be
determined,
4B
Chemical- None
Physical – None
27
Guidebook
HAZARD ANALYSIS – RAW PRODUCT,GROUND
Attachment 6
Process Step Food Safety
Hazard
Reasonably
Likely to
Occur?
Basis If Yes in Column 3,
What Measures Could
be Applied to Prevent,
Eliminate,or Reduce
the Hazard to an
Acceptable Level?
Critical Control
Point
Packaging/Labeling Biological,Pathogens
– parasitic (Trichina)
Yes Trichina has
historically occurred in
raw pork products,
Labels that clearly indicate
this is a raw product,along
with cooking instructions,
and the safe food handling
statement,
5B
Chemical – None
Physical – Metal
contamination
Yes Metal contamination
that may have come
into the establishment
or is contaminated
during the grinding
process must be
removed,
Functional metal detector is
on-line in the
packaging/labeling area to
remove metal
contamination,
6P
Finished Product
Storage (Cold)
Biological – Pathogens Yes Pathogens are
reasonably likely to
grow in this product if
temperature is not
maintained at or below
a level sufficient to
preclude their growth,
Maintain product
temperature at or below a
level sufficient to preclude
pathogen growth,
7B
Chemical – None
Physical - None
28
Guidebook
HAZARD ANALYSIS – RAW PRODUCT,GROUND
Attachment 6
Process Step Food Safety
Hazard
Reasonably
Likely to
Occur?
Basis If Yes in Column 3,
What Measures Could
be Applied to Prevent,
Eliminate,or Reduce
the Hazard to an
Acceptable Level?
Critical Control
Point
Shipping Biological – None
Chemical- None
Physical – None
29
Guidebook
Attachment 7
HACCP PLAN DEVELOPMENT FORM,MONITORING PROCEDURES
AND FREQUENCY
PROCESS CATEGORY,
PRODUCT,
PROCESS
STEP/CCP
CRITICAL LIMITS MONITORING PROCEDURES
*(WHO/WHAT/WHEN/HOW)
* 417.5(b),417.2(6),417.2(4)- Who refers to the requirement that records must be initialed; When –
to the time the specific event occurs; What – the measurement to determine compliance at the CCP;
and How - the method used to monitor the CCP,
30
Guidebook
Attachment 8
HACCP PLAN DEVELOPMENT FORM,CORRECTIVE ACTIONS
PROCESS CATEGORY,
PRODUCT,
PROCESS
STEP/CCP
CRITICAL LIMITS MONITORING PROCEDURES
(WHO/WHAT/WHEN/HOW)
*CORRECTIVE ACTIONS
*Be sure to include your planned actions to address all parts of § 417.3,
31
Guidebook
Attachment 9
HACCP PLAN
PROCESS CATEGORY,________________________________
PRODUCT EXAMPLE,_____________________________________________
CCP# and
Location
Critical
Limits
Monitoring
Procedures
and Frequency
HACCP Records Verification Procedures and
Frequency
Corrective Actions
Signature,__________________________________ Date,__________________________
32
Guidebook
Attachment 10
List of Some Typical Records of a HACCP System in
Operation
1,Ingredients
Records from all monitored CCPs,
Supplier certification documenting compliance with establishment’s specifications,
Establishment’s audit records verifying supplier compliance,
Storage temperature record for temperature-sensitive ingredients,
Storage time records of limited shelf-life ingredients,
2,Preparation
Records from all monitored CCPs,
Records verifying the continued adequacy of the food preparation procedures,
3,Packaging
Records indicating compliance with specifications for packaging materials,
Records indicating compliance with sealing specifications,
4,Finished product
Sufficient data and records to establish the efficacy of barriers in maintaining product
safety,
Sufficient data and records to establish the safe shelf-life of the product if age of
product can affect safety,
Documentation of the adequacy of the HACCP procedures from an authority
knowledgeable of the hazards involved and necessary controls,
33
Guidebook
5,Storage and distribution
Temperature records,
Records showing no product shipped after shelf-life date on temperature-sensitive
products,
6,Deviation and corrective action
Records of all actions taken following deviations at a CCP,
Reassessment records and modifications to the HACCP plan indicating approved
revisions and changes in ingredients,formulations,preparation,packaging,and
distribution control,as needed,
7,Employee training
Records indicating that employees responsible for implementation of the HACCP
plan understand the hazards,controls,and procedures,
34
Guidebook
APPENDIX A
35
Guidebook
PART 417--HAZARD ANALYSIS AND CRITICAL CONTROL POINT (HACCP)
SYSTEMS
§ 417.1 Definitions,
For purposes of this part,the following definitions shall apply,
Corrective action,Procedures to be followed when a deviation occurs,
Critical control point,A point,step,or procedure in a food process at which control can
be applied and,as a result,a food safety hazard can be prevented,eliminated,or reduced to
acceptable levels,
Critical limit,The maximum or minimum value to which a physical,biological,or
chemical hazard must be controlled at a critical control point to prevent,eliminate,or reduce to
an acceptable level the occurrence of the identified food safety hazard,
Food safety hazard,Any biological,chemical,or physical property that may cause a food
to be unsafe for human consumption,
HACCP System,The HACCP plan in operation,including the HACCP plan itself,
Hazard,SEE Food Safety Hazard,
Preventive measure,Physical,chemical,or other means that can be used to control an
identified food safety hazard,
Process-monitoring instrument,An instrument or device used to indicate conditions
during processing at a critical control point,
Responsible establishment official,The individual with overall authority on-site or a
higher level official of the establishment,
§ 417.2 Hazard Analysis and HACCP Plan,
(a) Hazard analysis,(1) Every official establishment shall conduct,or have conducted
for it,a hazard analysis to determine the food safety hazards reasonably likely to occur in the
production process and identify the preventive measures the establishment can apply to control
those hazards,The hazard analysis shall include food safety hazards that can occur before,
during,and after entry into the establishment,A food safety hazard that is reasonably likely to
occur is one for which a prudent establishment would establish controls because it historically
has occurred,or because there is a reasonable possibility that it will occur in the particular type
of product being processed,in the absence of those controls,
36
Guidebook
(2) A flow chart describing the steps of each process and product flow in the
establishment shall be prepared,and the intended use or consumers of the finished product shall
be identified,
(3) Food safety hazards might be expected to arise from the following,
(i) Natural toxins;
(ii) Microbiological contamination;
(iii) Chemical contamination;
(iv) Pesticides;
(v) Drug residues;
(vi) Zoonotic diseases;
(vii) Decomposition;
(viii) Parasites;
(ix) Unapproved use of direct or indirect food or color additives; and
(x) Physical hazards,
(b) The HACCP plan,(1) Every establishment shall develop and implement a written
HACCP plan covering each product produced by that establishment whenever a hazard analysis
reveals one or more food safety hazards that are reasonably likely to occur,based on the hazard
analysis conducted in accordance with paragraph (a) of this section,including products in the
following processing categories,
(i) Slaughter--all species,
(ii) Raw product--ground,
(iii) Raw product--not ground,
(iv) Thermally processed--commercially sterile,
(v) Not heat treated--shelf stable,
(vi) Heat treated--shelf stable,
(vii) Fully cooked--not shelf stable,
37
Guidebook
(viii) Heat treated but not fully cooked--not shelf stable,
(ix) Product with secondary inhibitors--not shelf stable,
(2) A single HACCP plan may encompass multiple products within a single processing
category identified in this paragraph,if the food safety hazards,critical control points,critical
limits,and procedures required to be identified and performed in paragraph (c) of this section are
essentially the same,provided that any required features of the plan that are unique to a specific
product are clearly delineated in the plan and are observed in practice,
(3) HACCP plans for thermally processed/commercially sterile products do not have to
address the food safety hazards associated with microbiological contamination if the product is
produced in accordance with the requirements of part 318,subpart G,or part 381,subpart X,of
this chapter,
(c) The contents of the HACCP plan,The HACCP plan shall,at a minimum,
(1) List the food safety hazards identified in accordance with paragraph (a) of this
section,which must be controlled for each process,
(2) List the critical control points for each of the identified food safety hazards,
including,as appropriate,
(i) Critical control points designed to control food safety hazards that could be
introduced in the establishment,and
(ii) Critical control points designed to control food safety hazards introduced outside the
establishment,including food safety hazards that occur before,during,and after entry into the
establishment;
(3) List the critical limits that must be met at each of the critical control points,Critical
limits shall,at a minimum,be designed to ensure that applicable targets or performance
standards established by FSIS,and any other requirement set forth in this chapter pertaining to
the specific process or product,are met;
(4) List the procedures,and the frequency with which those procedures will be
performed,that will be used to monitor each of the critical control points to ensure compliance
with the critical limits;
(5) Include all corrective actions that have been developed in accordance with § 417.3(a)
of this part,to be followed in response to any deviation from a critical limit at a critical control
point; and
(6) Provide for a recordkeeping system that documents the monitoring of the critical
control points,The records shall contain the actual values and observations obtained during
monitoring,
38
Guidebook
(7) List the verification procedures,and the frequency with which those procedures will
be performed,that the establishment will use in accordance with § 417.4 of this part,
(d) Signing and dating the HACCP plan,(1) The HACCP plan shall be signed and
dated by the responsible establishment individual,This signature shall signify that the
establishment accepts and will implement the HACCP plan,
(2) The HACCP plan shall be dated and signed,
(i) Upon initial acceptance;
(ii) Upon any modification; and
(iii) At least annually,upon reassessment,as required under § 417.4(a)(3) of this part,
(e) Pursuant to 21 U.S.C,456,463,608,and 621,the failure of an establishment to
develop and implement a HACCP plan that complies with this section,or to operate in
accordance with the requirements of this part,may render the products produced under those
conditions adulterated,
§ 417.3 Corrective actions,
(a) The written HACCP plan shall identify the corrective action to be followed in
response to a deviation from a critical limit,The HACCP plan shall describe the corrective
action to be taken,and assign responsibility for taking corrective action,to ensure,
(1) The cause of the deviation is identified and eliminated;
(2) The CCP will be under control after the corrective action is taken;
(3) Measures to prevent recurrence are established; and
(4) No product that is injurious to health or otherwise adulterated as a result of the
deviation enters commerce,
(b) If a deviation not covered by a specified corrective action occurs,or if another
unforeseen hazard arises,the establishment shall,
(1) Segregate and hold the affected product,at least until the requirements of paragraphs
(b)(2) and (b)(3) of this section are met;
(2) Perform a review to determine the acceptability of the affected product for
distribution;
39
Guidebook
(3) Take action,when necessary,with respect to the affected product to ensure that no
product that is injurious to health or otherwise adulterated,as a result of the deviation,enters
commerce;
(4) Perform or obtain reassessment by an individual trained in accordance with § 417.7 of
this part,to determine whether the newly identified deviation or other unforeseen hazard should
be incorporated into the HACCP plan,
(c) All corrective actions taken in accordance with this section shall be documented in
records that are subject to verification in accordance with § 417.4(a)(2)(iii) and the
recordkeeping requirements of § 417.5 of this part,
§ 417.4 Validation,Verification,Reassessment,
(a) Every establishment shall validate the HACCP plan's adequacy in controlling the
food safety hazards identified during the hazard analysis,and shall verify that the plan is being
effectively implemented,
(1) Initial validation,Upon completion of the hazard analysis and development of the
HACCP plan,the establishment shall conduct activities designed to determine that the HACCP
plan is functioning as intended,During this HACCP plan validation period,the establishment
shall repeatedly test the adequacy of the CCP's,critical limits,monitoring and recordkeeping
procedures,and corrective actions set forth in the HACCP plan,Validation also encompasses
reviews of the records themselves,routinely generated by the HACCP system,in the context of
other validation activities,
(2) Ongoing verification activities,Ongoing verification activities include,but are not
limited to,
(i) The calibration of process-monitoring instruments;
(ii) Direct observations of monitoring activities and corrective actions; and
(iii) The review of records generated and maintained in accordance with § 417.5(a)(3) of
this part,
(3) Reassessment of the HACCP plan,Every establishment shall reassess the adequacy
of the HACCP plan at least annually and whenever any changes occur that could affect the
hazard analysis or alter the HACCP plan,Such changes may include,but are not limited to,
changes in,raw materials or source of raw materials; product formulation; slaughter or
processing methods or systems; production volume; personnel; packaging; finished product
distribution systems; or,the intended use or consumers of the finished product,The
reassessment shall be performed by an individual trained in accordance with § 417.7 of this part,
The HACCP plan shall be modified immediately whenever a reassessment reveals that the plan
no longer meets the requirements of § 417.2(c) of this part,
40
Guidebook
(b) Reassessment of the hazard analysis,Any establishment that does not have a
HACCP plan because a hazard analysis has revealed no food safety hazards that are reasonably
likely to occur shall reassess the adequacy of the hazard analysis whenever a change occurs that
could reasonably affect whether a food safety hazard exists,Such changes may include,but are
not limited to,changes in,raw materials or source of raw materials; product formulation;
slaughter or processing methods or systems; production volume; packaging; finished product
distribution systems; or,the intended use or consumers of the finished product,
§ 417.5 Records,
(a) The establishment shall maintain the following records documenting the
establishment's HACCP plan,
(1) The written hazard analysis prescribed in § 417.2(a) of this part,including all
supporting documentation;
(2) The written HACCP plan,including decision making documents associated with the
selection and development of CCP's and critical limits,and documents supporting both the
monitoring and verification procedures selected and the frequency of those procedures,
(3) Records documenting the monitoring of CCP's and their critical limits,including the
recording of actual times,temperatures,or other quantifiable values,as prescribed in the
establishment's HACCP plan; the calibration of process-monitoring instruments; corrective
actions,including all actions taken in response to a deviation; verification procedures and results;
product code(s),product name or identity,or slaughter production lot,Each of these records
shall include the date the record was made,
(b) Each entry on a record maintained under the HACCP plan shall be made at the time
the specific event occurs and include the date and time recorded,and shall be signed or initialed
by the establishment employee making the entry,
(c) Prior to shipping product,the establishment shall review the records associated with
the production of that product,documented in accordance with this section,to ensure
completeness,including the determination that all critical limits were met and,if appropriate,
corrective actions were taken,including the proper disposition of product,Where practicable,
this review shall be conducted,dated,and signed by an individual who did not produce the
record(s),preferably by someone trained in accordance with § 417.7 of this part,or the
responsible establishment official,
(d) Records maintained on computers,The use of records maintained on computers is
acceptable,provided that appropriate controls are implemented to ensure the integrity of the
electronic data and signatures,
(e) Record retention,(1) Establishments shall retain all records required by paragraph
(a)(3) of this section as follows,for slaughter activities for at least one year; for refrigerated
41
Guidebook
product,for at least one year; for frozen,preserved,or shelf-stable products,for at least two
years,
(2) Off-site storage of records required by paragraph (a)(3) of this section is permitted
after six months,if such records can be retrieved and provided,on-site,within 24 hours of an
FSIS employee's request,
(f) Official review,All records required by this part and all plans and procedures
required by this part shall be available for official review and copying,
§ 417.6 Inadequate HACCP Systems,
A HACCP system may be found to be inadequate if,
(a) The HACCP plan in operation does not meet the requirements set forth in this part;
(b) Establishment personnel are not performing tasks specified in the HACCP plan;
(c) The establishment fails to take corrective actions,as required by § 417.3 of this part;
(d) HACCP records are not being maintained as required in § 417.5 of this part; or
(e) Adulterated product is produced or shipped,
§ 417.7 Training,
(a) Only an individual who has met the requirements of paragraph (b) of this section,but
who need not be an employee of the establishment,shall be permitted to perform the following
functions,
(1) Development of the HACCP plan,in accordance with § 417.2(b) of this part,which
could include adapting a generic model that is appropriate for the specific product; and
(2) Reassessment and modification of the HACCP plan,in accordance with § 417.3 of
this part,
(b) The individual performing the functions listed in paragraph (a) of this section shall
have successfully completed a course of instruction in the application of the seven HACCP
principles to meat or poultry product processing,including a segment on the development of a
HACCP plan for a specific product and on record review,
§ 417.8 Agency verification,
FSIS will verify the adequacy of the HACCP plan(s) by determining that each HACCP
plan meets the requirements of this part and all other applicable regulations,Such verification
may include,
42
Guidebook
(a) Reviewing the HACCP plan;
(b) Reviewing the CCP records;
(c) Reviewing and determining the adequacy of corrective actions taken when a
deviation occurs;
(d) Reviewing the critical limits;
(e) Reviewing other records pertaining to the HACCP plan or system;
(f) Direct observation or measurement at a CCP;
(g) Sample collection and analysis to determine the product meets all safety standards;
and
(h) On-site observations and record review,
43
Guidebook
APPENDIX B
44
Guidebook
References for HACCP Teams
1. Agriculture Canada,Food Safety Enhancement Program – HACCP Implementation
Manual,Camelot Drive,Nepean,Ontario,Canada,1996,
2. American Meat Institute Foundation,HACCP,The Hazard Analysis and Critical
Control Point System in the Meat and Poultry Industry,Washington,D.C.,1994,
Useful sections in particular are,
Chapter 3 – microbiological hazards,pp,15-26
Chapter 4 – chemical hazards,pp,27-32
Chapter 5 – physical hazards,pp,33-35
Appendix A – NACMCF HACCP
Appendix C – Model HACCP plans
3. Baker,D.A,Application of Modeling in HACCP Plan Development,Int,J,Food
Microbiol,25:251-261,1995,
4. Corlett,D.A.,Jr,and Stier,R.F,Risk Assessment within the HACCP System,Food
Control 2:71-72,1991,
5. Council for Agriculture Science and Technology,Risks Associated with Foodborne
Pathogens,February 1993,
6. Easter,M.C.,et al,The Role of HACCP in the Management of Food Safety and
Quality,J,Soc,Dairy Technol,47:42-43,1994,
7. Environmental Protection Agency,Tolerances for Pesticides in Foods,Title 40,
Code of Federal Regulations,Part 185,U.S,Government Printing Office,
Washington,D.C.,1998,
8. Food and Drug Administration,The Food Defect Action Levels,FDA/CFSAN,
Washington,D.C.,1998,
9. Food and Drug Administration,Fish and Fishery Products Hazards and Control
Guide --Get Hooked on Seafood Safety,Office of Seafood,Washington,D.C.,1994,
10,International Commission on Microbiological Specification for Foods,HACCP in
Microbiological Safety and Quality,Blackwell Scientific Publications,Oxford,1988,
Useful sections in particular are,
Chapter 10 – raw meat and poultry,pp,176-193
Chapter 11 – roast beef,pp,234-238
Chapter 11 – canned ham,pp,238-242
45
Guidebook
11,International Commission on Microbiological Specification for Foods,
Microorganisms in Foods 4,Application of Hazard Analysis and Critical Control
Point (HACCP) Systems to Ensure Microbiological Safety and Quality,Blackwell
Scientific Publications,Boston,1989
12,National Advisory Committee on Microbiological Criteria for Foods,March 20,
1992 -- Hazard Analysis and Critical Control Point System,Int,J,Food Microbiol,
16,1-23,1993,
13,National Advisory Committee on Microbiological Criteria for Foods,Adopted
August 14,1997-- Hazard Analysis and Critical Control Point Principles and
Application Guidelines,J,Food Protect,61(9),1246-1259,1998,
14,National Advisory Committee on Microbiological Criteria for Foods,DRAFT
document - FSIS Microbiological Hazard Identification Guide for Meat and Poultry
Components of Products Produced by Very Small Plants,1-22,August 1999,
15,National Advisory Committee on Microbiological Criteria for Foods,June 1993 --
Report on Generic HACCP for Raw Beef,Food Microbiol,10,449-488,1994,
16,National Research Council,An Evaluation of the Role of Microbiological Criteria for
Foods and Food Ingredients,National Academy Press,Washington,D.C.,1985,
Useful sections in particular are,
Chapter 4 – microbiological hazards,pp,72-103
Chapter 9 – raw meat,pp,193-199
Chapter 9 – processed meats,pp,199-216
17,Notermans,S.,et al,The HACCP Concept,Identification of Potentially Hazardous
Microorganisms,Food Microbiol,11:203-214,1994,
18,Pierson M.D,and Dutson,T,Editors,HACCP in Meat,Poultry,and Fish
Processing,Blackie Academic & Professional,Glasgow,1995,
Useful sections in particular are,
Chapter 4 – meat and poultry slaughter,pp,58-71
Chapter 5 – processed meats,pp,72-107
Chapter 7 – risk analysis,pp,134-154
Chapter 13 – predictive modeling,pp,330-354
19,Pierson,M.D,and Corlett,D.A.,Jr,Editors,HACCP Principles and Applications,
Van Nostrand Reinhold,New York,1992,
20,Stevenson,K.E,and Bernard,D.T,Editors,HACCP,Establishing Hazard Analysis
Critical Control Point Programs.,A Workshop Manual,The Food Processors
Institute,Washington,D.C.,1995,
46
Guidebook
Useful sections in particular are,
Chapter 11 – forms for hazard analysis,CCPs,critical limits,HACCP
master sheet,example HACCP for breaded chicken
21,Stevenson,K.E,and Bernard,D.T,Editors,HACCP,A Systematic Approach to
Food Safety,3
rd
Edition,The Food Processors Institute,Washington,D.C.,1999,
22,Tompkin,R.B,The Use of HACCP in the Production of Meat and Poultry Products,
J,Food Protect,53(9),795-803,1990,
23,Tompkin,R.B,The Use of HACCP for Producing and Distributing Processed Meat
and Poultry Products,In Advances in Meat Research,Volume 10,Hazard Analysis
Critical Control Point in Meat,Poultry and Seafoods,Chapman & Hall,1995,
47
Guidebook
APPENDIX C
48
-----------------------------------------------------------------------
-----------------------------------------------------------------------
Livestock Carcasses and Poultry Carcasses Contaminated With
Visible Fecal Material
[Federal Register,November 28,1997 (Volume 62,Number 229)]
[Rules and Regulations]
[Page 63254-63255]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr28no97-2]
=======================================================================
DEPARTMENT OF AGRICULTURE
Food Safety and Inspection Service
9 CFR Parts 301,307,308,310,318,381,416,and 417
[Docket No,97-067N]
Livestock Carcasses and Poultry Carcasses Contaminated With
Visible Fecal Material
AGENCY,Food Safety and Inspection Service,USDA,
ACTION,Notice on complying with food safety standards under the HACCP
system regulations,
SUMMARY,The Food Safety and Inspection Service is publishing this
notice to assure that the owners and operators of federally inspected
slaughter establishments are aware that the Agency views its,zero
tolerance” for visible fecal material as a food safety standard,Fecal
material is a vehicle for microbial pathogens,and microbiological
contamination is a food safety hazard that is reasonably likely to
occur in the slaughter production process,In controlling
microbiological contamination,a hazard analysis and critical control
point plan for slaughter must be designed,among other things,to
ensure that,by the point of post-mortem inspection of livestock
carcasses or when poultry carcasses enter the chilling tank,no visible
fecal material is present,
FOR FURTHER INFORMATION CONTACT,Patricia F,Stolfa,Assistant Deputy
Administrator,Regulations and Inspection Methods,Food Safety and
Inspection Service,Washington,DC 20250-3700; (202) 205-0699,
SUPPLEMENTARY INFORMATION,The Food Safety and Inspection Service
(FSIS) administers a regulatory program under the Federal Meat
Inspection Act (FMIA) (21 U.S.C,601 et seq.) and the Poultry Products
Inspection Act (PPIA) (21 U.S.C,451 et seq.) to protect the health and
welfare of consumers by preventing the distribution of livestock
products and poultry products that are unwholesome,adulterated,or
FSIS Form 2630-9 (6/86) EQUAL OPPORTUNITY IN EMPLOYMENT AND SERVICES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
Guidebook
misbranded,A livestock product or poultry product is adulterated under
any of a number of circumstances,including the following,if it bears
or contains any poisonous or deleterious substance which may render it
injurious to health,unless when the substance is not an added
substance,the quantity in or on the article does not ordinarily render
it injurious to health; if it consists in whole or in part of any
filthy,putrid,or decomposed substance or is for any other reason
unsound,unhealthful,unwholesome,or otherwise
[[Page 63255]]
unfit for human food; or if it has been prepared,packed,or held under
unsanitary conditions whereby it may have become contaminated with
filth or whereby it may have been rendered injurious to health (21
U.S.C,453(g)(1),(g)(3),and (g)(4) and 601(m)(1),(m)(3),and
(m)(4)),Both the FMIA and the PPIA include requirements for government
inspection and prohibit transactions in products required to be
inspected unless they have been ``inspected and passed'' or if they are
adulterated (21 U.S.C,458(a)(2) and 610(c)),
FSIS enforces a ``zero tolerance'' standard for visible fecal
material on carcasses and carcass parts at inspected establishments
that slaughter livestock or poultry,This standard is reflected in the
Agency's regulations under the FMIA and the PPIA (9 CFR chapter III,
subchapter A and subchapter C,respectively),which require (among
other things) that establishments handle livestock carcasses and
carcass parts to prevent contamination with fecal material and promptly
remove contamination if it occurs (Sec,310.18) and that establishments
prevent poultry carcasses contaminated with visible fecal material from
entering the chilling tank (Sec,381.65(e)),When inspection program
personnel observe fecal material at post-mortem livestock inspection or
thereafter (i.e.,at or after the final rail) under the FMIA or when
poultry carcasses are about to enter the chilling tank or thereafter
(i.e.,at any point after the final pre-chiller wash) under the PPIA,
they condemn affected carcasses and carcass parts unless the
contamination is removed in accordance with regulatory requirements,
The Agency is publishing this notice to assure that the owners and
operators of federally inspected slaughter establishments are aware
that FSIS regards its zero tolerance for visible fecal material as a
food safety standard under both the FMIA and the PPIA,Reiterating the
Agency's position is particularly appropriate now,as federally
inspected establishments prepare to comply with the hazard analysis and
critical control point (HACCP) system regulations (part 417),<SUP>1</SUP>
\1\ Part 417 requirements,as well as pathogen reduction
performance standards for Salmonella in establishments that
slaughter cattle,swine,chickens,or turkeys,prepare ground beef
or fresh pork sausage,or process ground chicken or turkey
(Secs,310.25(b) and 381.94(b)) will apply as of January 26,1998,
in establishments with 500 or more employees; January 25,1999,in
establishments with 10 or more but fewer than 500 employees (unless
the establishment has annual sales of less than $2.5 million); and
January 25,2000,in establishments with fewer than 10 employees or
annual sales of less than $2.5 million,
50
Guidebook
The essence of FSIS's position is that fecal material is a vehicle
for microbial pathogens,and microbiological contamination is a food
safety hazard that is reasonably likely to occur in the slaughter
production process (Sec,417.2(a) and (b)),Consequently,HACCP plans
must control for microbiological contamination at slaughter,and to
meet the zero tolerance standard,an establishment's controls must
(among other things) include limits that ensure that no visible fecal
material is present by the point of post-mortem inspection of livestock
carcasses or before poultry carcasses enter the chilling tank
(Sec,417.2(c)),
In the Pathogen Reduction-HACCP Systems final rule (61 FR 38806,
July 25,1996),FSIS explained the reasoning underlying its position on
fecal contamination,and at the beginning of this year,FSIS addressed
the role of its zero tolerance for visible fecal material on poultry
carcasses in the final rule that codified the standard under the PPIA
(62 FR 5139,February 4,1997),Preparation for implementation of the
HACCP system regulations has not changed the Agency's conclusions about
the appropriateness of this standard,under the FMIA as well as the
PPIA,
As the Agency stated in the Pathogen Reduction-HACCP Systems final
rule (61 FR 38837),
In slaughter establishments,fecal contamination of carcasses is
the primary avenue for contamination by pathogens,Pathogens may
reside in fecal material and ingesta,both within the
gastrointestinal tract and on the exterior surfaces of animals going
to slaughter,Therefore,without care being taken in handling and
dressing procedures during slaughter and processing,the edible
portions of the carcass can become contaminated with bacteria
capable of causing illness in humans,Additionally,once introduced
into the establishment environment,the organisms may be spread from
carcass to carcass,
Because the microbial pathogens associated with fecal
contamination are the single most likely source of potential food
safety hazard in slaughter establishments,preventing and removing
fecal contamination and associated bacteria are vital
responsibilities of slaughter establishments,Further,because such
contamination is largely preventable,controls to address it will be
a critical part of any slaughter establishment's HACCP plan,Most
slaughter establishments already have in place procedures designed
to prevent and remove visible fecal contamination,
As noted in the zero tolerance final rule and confirmed today with
respect to livestock as well as poultry,establishments that process
animals must adopt controls that they can demonstrate are effective in
reducing the occurrence of microbial pathogens,including controls that
prevent the fecal contamination of carcasses (62 FR 5140),Under the
HACCP system regulations,critical control points to eliminate
contamination with visible fecal material are predictable and essential
components of all slaughter establishments' HACCP plans,Initial
validation of a HACCP plan for slaughter and monitoring thereunder,as
verified and documented in establishment records,must demonstrate the
effective operation of the plan's controls on a continuing basis
(Secs,417.3(a),417.4,and 417.5),
FSIS personnel will continue to verify compliance with the zero
tolerance standard in slaughter establishments that are subject to part
417 requirements,The Agency will use visual observations and other
51
Guidebook
findings by FSIS personnel in evaluating the effectiveness of an
establishment's preventive controls and corrective actions for fecal
contamination (Secs,417.6 and 417.8),The presence of visible fecal
contamination on livestock carcasses presented for post-mortem
inspection or poultry carcasses entering the chilling tank will mean
that establishment controls have failed; repeated failures will
evidence that establishment corrective actions have failed to prevent
recurrence and,thus,possible system inadequacy,
In addition to enforcing the zero tolerance for visible fecal
material,FSIS will use the results of establishment testing for
generic E,coli (Escherichia coli Biotype I,as already required by
Sec,310.25(a) or Sec,381.94(a)) in assessing how well an
establishment is controlling its slaughter and dressing processes to
prevent fecal contamination,The pathogen reduction performance
standards for Salmonella (Secs,310.25(b) and 381.94(b)),which FSIS
will enforce through its own testing program,will complement the zero
tolerance standard and E,coli testing,
Done at Washington,D.C.,on November 18,1997,
Thomas J,Billy,
Administrator,
[FR Doc,97-31176 Filed 11-26-97; 8:45 am]
BILLING CODE 3410-DM-P
52
-----------------------------------------------------------------------
-----------------------------------------------------------------------
Guidebook
Contents of HACCP Plans,Critical Control Points
[Federal Register,January 30,1998 (Volume 63,Number 20)]
[Rules and Regulations]
[Page 4560-4562]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr30ja98-2]
DEPARTMENT OF AGRICULTURE
Food Safety and Inspection Service
9 CFR Part 417
[Docket No,97-082N]
Contents of HACCP Plans; Critical Control Points
AGENCY,Food Safety and Inspection Service,USDA,
ACTION,Compliance with the HACCP system regulations,
SUMMARY,The Food Safety and Inspection Service (FSIS) is publishing
this document to ensure that the owners and operators of federally
inspected establishments are aware that the identification of
appropriate critical
[[Page 4561]]
control points is crucial to complying with the Agency's regulations on
hazard analysis and critical control point (HACCP) systems,The HACCP
system regulations require that a HACCP plan list critical control
points for each food safety hazard identified as reasonably likely to
occur in the production process,The number of critical control points
will depend upon the production process and the hazard,but a HACCP
plan must specify as critical control points the points,steps,or
procedures at which control can be applied and,as measured by critical
limits,occurrence of the hazard can be prevented,eliminated,or
reduced to an acceptable level,and at a minimum,the critical limits
must be designed to ensure that applicable targets or performance
standards established by FSIS,and any other requirement in the
Agency's regulations pertaining to the specific process or product,are
met,These requirements implement FSIS's judgment that whenever a food
safety hazard is reasonably likely to occur in the production process,
by applying control measures,the establishment can at least reduce the
hazard to an acceptable level,even if it cannot entirely prevent or
eliminate its occurrence,
FOR FURTHER INFORMATION CONTACT,Patricia F,Stolfa,Assistant Deputy
Administrator,Regulations and Inspection Methods,Food Safety and
Inspection Service,Washington,DC 20250-3700; (202) 205-0699,
53
-----------------------------------------------------------------------
-----------------------------------------------------------------------
Guidebook
SUPPLEMENTARY INFORMATION,The Food Safety and Inspection Service
(FSIS) administers a regulatory program under the Federal Meat
Inspection Act (FMIA) (21 U.S.C,601 et seq.) and the Poultry Products
Inspection Act (PPIA) (21 U.S.C,451 et seq.) to protect the health and
welfare of consumers by preventing the distribution of livestock
products and poultry products that are unwholesome,adulterated,or
misbranded,To further the goal of reducing the risk of foodborne
illness from meat and poultry products to the maximum extent possible,
FSIS issued the Pathogen Reduction-Hazard Analysis and Critical Control
Point (HACCP) Systems final rule (61 FR 38806,July 25,1996),
The HACCP system regulations,part 417,<SUP>1</SUP> require that
every federally inspected establishment conduct,or have conducted for
it,a hazard analysis to determine the food safety hazards reasonably
likely to occur in the production process and identify the preventive
measures the establishment can apply to control those hazards
(Sec,417.2(a)),Whenever a hazard analysis reveals one or more food
safety hazards that are reasonably likely to occur,the establishment
must develop and implement a HACCP plan,or plans,to control those
hazards (Sec,417.2(b)),Although it is possible that a hazard analysis
conducted in accordance with the regulations will reveal no food safety
hazard that is reasonably likely to occur,as the Agency stated when it
issued the regulations,FSIS is not aware of any meat or poultry
production process that can be deemed,categorically,to pose no likely
hazards (61 FR 38824).<SUP>2</SUP>
\1\ Part 417 requirements will apply as of January 26,1998,in
establishments with 500 or more employees; January 25,1999,in
establishments with 10 or more but fewer than 500 employees (unless
the establishment has annual sales of less than $2.5 million); and
January 25,2000,in establishments with fewer than 10 employees or
annual sales of less than $2.5 million,
\2\ Food safety hazards include any biological,chemical,or
physical property that may cause a food to be unsafe for human
consumption (Sec,417.1),
For purposes of part 417,a critical control point (CCP) is a
point,step,or procedure in a food process at which control can be
applied and,as a result,a food safety hazard can be prevented,
eliminated,or reduced to acceptable levels (Sec,417.1).) Every HACCP
plan must ``list the critical control points for each of the identified
food safety hazards,including,as appropriate:''
(i) Critical control points designed to control food safety
hazards that could be introduced in the establishment,and
(ii) Critical control points designed to control food safety
hazards introduced outside the establishment,including food safety
hazards that occur before,during,and after entry into the
establishment * * *
(Sec,417.2(c)(2)),The plan also must comply with the related
requirements to specify the critical limits (maximum and minimum
values) to be met at CCP's,the corrective actions to be followed in
response to deviations from critical limits at CCP's,and the
monitoring and verification procedures to ensure appropriate corrective
actions if and when those deviations occur (Secs,417.1,417.2(c),
417.3(a),and 417.4(a)),At a minimum,critical limits must be designed
54
-----------------------------------------------------------------------
-----------------------------------------------------------------------
Guidebook
to ensure that applicable targets or performance standards established
by FSIS,and any other requirement in FSIS's regulations (9 CFR chapter
III) pertaining to the specific process or product,are met
(Sec,417.2(c)(3)),
It has come to FSIS's attention that in developing HACCP plans,
some persons are viewing CCP's so narrowly that they risk noncompliance
with regulatory requirements,FSIS is concerned that some
establishments may be relying solely on HACCP concepts and theory,
without evaluating CCP's in accordance with regulatory requirements,
The Agency is publishing this notice to ensure that the owners and
operators of federally inspected establishments are aware that the
identification of appropriate critical control points is crucial,
The number of critical control points will depend upon the
production process and the hazard,FSIS will treat failure to specify
at least one CCP for each food safety hazard identified in accordance
with the regulations as reasonably likely to occur as a failure to
develop and implement a HACCP plan that complies with Sec,417.2
(Sec,417.2(e)),The only exception,as specified in Sec,417.2(b)(3),
is for food safety hazards associated with microbiological
contamination,HACCP plans that cover thermally processed/commercially
sterile products produced in accordance with the current canning
regulations (part 318,subpart G,or part 381,subpart X) need not,at
this time,address microbial hazards.<SUP>3</SUP>
\3\ FSIS intends to convert the canning regulations to
performance standards,which are more consistent with HACCP (61 FR
38824),
FSIS anticipates that to operate in accordance with part 417,many
establishments will find that for each identified hazard,they need
more than one CCP,particularly if they are producing raw products,The
Agency believes that depending upon a single CCP increases
establishment exposure to production-disrupting corrective actions that
affect large amounts of product,While FSIS is not prepared to say that
compliance cannot be achieved with a single CCP when,for example,a
product is treated sufficiently to be shelf stable,even though it is
not commercially sterile,the Agency is concerned that establishments
may be viewing CCP's too restrictively to ensure compliance with the
regulations,
The part 417 requirements addressed in this notice implement the
Agency's conclusion that whenever a food safety hazard is reasonably
likely to occur in the production process,even if an establishment
cannot entirely prevent or eliminate occurrence of the hazard,by
applying control measures,the establishment can at least reduce it to
an acceptable level,Part 417 requires all federally inspected
establishments to take the prudent,preventive approach and develop
systematic measures for controlling such hazards,
[[Page 4562]]
Done at Washington,D.C.,on,January 26,1998,
Thomas J,Billy,
Administrator,
[FR Doc,98-2297 Filed 1-29-98; 8:45 am]
BILLING CODE 3410-DM-P
55
-----------------------------------------------------------------------
-----------------------------------------------------------------------
Guidebook
Contents of HACCP Plans
[Federal Register,January 30,1998 (Volume 63,Number 20)]
[Rules and Regulations]
[Page 4562]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr30ja98-3]
DEPARTMENT OF AGRICULTURE
Food Safety and Inspection Service
9 CFR Part 417
[Docket No,97-074N]
Contents of HACCP Plans
AGENCY,Food Safety and Inspection Service,USDA,
ACTION,Compliance with the HACCP system regulations,
SUMMARY,The Food Safety and Inspection Service is publishing this
document to ensure that the owners and operators of federally inspected
establishments are aware that its hazard analysis and critical control
point (HACCP) system regulations require that an HACCP plan be a self-
contained document,In particular,the Agency does not view references
to good manufacturing practices,or establishment actions in accordance
with good manufacturing practices,as satisfying the requirements for
the contents of an HACCP plan,Among other things,an HACCP plan must
list the critical control points for each food safety hazard reasonably
likely to occur in the production process,the critical limits that
must be met at each of the critical control points,and the procedures,
and frequency with which they will be performed,that will be used to
monitor each critical control point to ensure compliance with critical
limits and to verify that the plan is being effectively implemented,An
HACCP plan also must identify the corrective actions to be followed in
response to deviations from critical limits at critical control points,
FOR FURTHER INFORMATION CONTACT,Patricia F,Stolfa,Assistant Deputy
Administrator,Regulations and Inspection Methods,Food Safety and
Inspection Service,Washington,DC 20250-3700; (202) 205-0699,
SUPPLEMENTARY INFORMATION,The Food Safety and Inspection Service
(FSIS) administers a regulatory program under the Federal Meat
Inspection Act (FMIA) (21 U.S.C,601 et seq.) and the Poultry Products
Inspection Act (PPIA) (21 U.S.C,451 et seq.) to protect the health and
welfare of consumers by preventing the distribution of livestock
products and poultry products that are unwholesome,adulterated,or
misbranded,To further the goal of reducing the risk of foodborne
56
-----------------------------------------------------------------------
-----------------------------------------------------------------------
Guidebook
illness from meat and poultry products to the maximum extent possible,
FSIS issued the Pathogen Reduction-Hazard Analysis and Critical Control
Point (HACCP) Systems final rule (61 FR 38806,July 25,1996),As
amended by that rule,FSIS's regulations require federally inspected
establishments to take preventive and corrective measures at each stage
of the food production process where food safety hazards occur,
The regulations on HACCP systems,part 417,* require a hazard
analysis to determine the food safety hazards reasonably likely to
occur in the production process and identify the preventive measures an
establishment can apply to control them (Sec,417.2(a)(1)) and,
whenever this analysis reveals one or more such hazards,development
and implementation of a written HACCP plan (Sec,417.2(b)(1)),In
Sec,417.2(c),the regulations specify minimum requirements for the
contents of each HACCP plan,including requirements to list the food
safety hazards for each process; list the critical control points for
each of the identified hazards; list the critical limits that must be
met at each of the critical control points; list the procedures,and
frequency with which they will be performed,that will be used to
monitor each of the critical control points to ensure compliance with
the critical limits; and list the verification procedures,and the
frequency with which they will be performed,that the establishment
will use in accordance with Sec,417.4 (i.e.,to verify that the plan
is being effectively implemented) (paragraphs (c)(1),(c)(2),(c)(3),
(c)(4),and (c)(7) of Sec,417.2),In addition,a HACCP plan must
include all corrective actions that have been developed in accordance
with Sec,417.3(a),which requires the identification of the corrective
action to be followed in response to a deviation from a critical limit
(Sec,417.2(c)(5)),
* Part 417 requirements will apply as of January 26,1998,in
establishments with 500 or more employees; January 25,1999,in
establishments with 10 or more but fewer than 500 employees (unless
the establishment has annual sales of less than $2.5 million); and
January 25,2000,in establishments with fewer than 10 employees or
annual sales of less than $2.5 million,
Given the explicit requirements to list critical control points,
critical limits,and monitoring and verification procedures and to
develop and identify corrective actions,and the Agency's statement,in
issuing part 417,that it was clarifying requirements for the
identification of critical control points within a HACCP plan (61 FR
38825),FSIS is concerned that some industry members and consultants to
industry think that they can comply with Sec,417.2(c) by referring to
good manufacturing practices,or establishment actions in accordance
with good manufacturing practices,While FSIS has considered good
manufacturing practices in developing some requirements that protect
the public against livestock products and poultry products that are
misbranded or economically adulterated (21 U.S.C,453 and 601),the
Agency has not adopted specific good manufacturing practices as part of
its regulations,
The Agency is publishing this notice to ensure that the owners and
operators of federally inspected establishments are aware that
references to good manufacturing practices,or establishment actions in
accordance with good manufacturing practices,rather than stating the
critical control points,critical limits,monitoring and verification
57
Guidebook
procedures,and corrective actions themselves is insufficient to
satisfy the requirements of Sec,417.5(c),Part 417 requires that a
HACCP plan be a self-contained document,
Moreover,the function of critical control points and critical
limits is to prevent,eliminate,or reduce to an acceptable level one
or more food safety hazards,By definition,critical limits are maximum
and minimum values (Sec,417.1),and by regulation,critical limits
must be designed,at a minimum,to ensure that applicable targets or
performance standards established by FSIS,and any other requirement in
FSIS's regulations (9 CFR chapter III) pertaining to the specific
process or product,are met (Sec,417.2(c)(3)),To determine whether
critical limits are met and,if not,prevent the distribution of
adulterated food and future deviations,the regulations require plan-
specific monitoring,verification,and corrective action procedures,
Done at Washington,D.C.,on,January 26,1998,
Thomas J,Billy,
Administrator,
[FR Doc,98-2296 Filed 1-29-98; 8:45 am]
BILLING CODE 3410-DM-P
58
-----------------------------------------------------------------------
-----------------------------------------------------------------------
Guidebook
Establishment Review of Product Production Records
[Federal Register,March 6,1998 (Volume 63,Number 44)]
[Rules and Regulations]
[Page 11104-11105]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr06mr98-3]
DEPARTMENT OF AGRICULTURE
Food Safety and Inspection Service
9 CFR Part 417
[Docket No,98-003N]
Establishment Review of Product Production Records
AGENCY,Food Safety and Inspection Service,USDA,
ACTION,Notice on complying with the HACCP system regulations,
SUMMARY,The Food Safety and Inspection Service is publishing this
document to provide information to owners and operators of federally
inspected establishments about what actions they must take to comply
with the requirement,in the hazard analysis and critical control point
system regulations,to review the records associated with production of
a product prior to its shipment for distribution,The regulations do
not prescribe how establishments meet this requirement and,thus,are
sufficiently flexible to accommodate various records' review schemes,
However,establishments must determine that all critical limits were
met and,when appropriate,that corrective actions were taken,
Establishments must also ensure the completeness of their records
before shipping the product for distribution,
FOR FURTHER INFORMATION CONTACT,Patricia F,Stolfa,Assistant Deputy
Administrator,Regulations and
[[Page 11105]]
Inspection Methods,Food Safety and Inspection Service,Washington,DC
20250-3700; (202) 205-0699,
SUPPLEMENTARY INFORMATION,The Food Safety and Inspection Service
(FSIS) administers a regulatory program under the Federal Meat
Inspection Act (FMIA) (21 U.S.C,601 et seq.) and the Poultry Products
Inspection Act (PPIA) (21 U.S.C,451 et seq.) to protect the health and
welfare of consumers by preventing the distribution of livestock
products and poultry products that are unwholesome,adulterated,or
misbranded,To further the goal of reducing the risk of foodborne
59
-----------------------------------------------------------------------
-----------------------------------------------------------------------
Guidebook
illness from meat and poultry products to the maximum extent possible,
FSIS issued part 417 of the regulations,Hazard Analysis and Critical
Control Point (HACCP) Systems.*
* Part 417 requirements will apply as of January 26,1998,in
establishments with 500 or more employees; January 25,1999,in
establishments with 10 or more but fewer than 500 employees (unless
the establishment has annual sales of less than $2.5 million); and
January 25,2000,in establishments with fewer than 10 employees or
annual sales of less than $2.5 million,
Part 417 requires federally inspected establishments to determine
the food safety hazards reasonably likely to occur in the production
process and to develop and implement a HACCP plan,or plans,to control
these hazards (Sec,417.2(a),(b),and (c)),Under part 417,
establishments control food safety hazards through monitoring
procedures that apply critical limits at critical control points and,
when deviations occur,by taking corrective actions that restore
establishment control and keep adulterated food out of commerce,as
documented in records that are subject to establishment verification
(Secs,417.2(c),417.3,and 417.5),
To ensure that HACCP plans are implemented effectively and function
as intended to control food safety hazards and prevent the distribution
of adulterated livestock products and poultry products,part 417 also
requires that establishments conduct validation and verification
activities (Sec,417.4(a)),Verification includes review of the records
that the establishment must keep to document a HACCP plan in operation
(Sec,417.5(a)(3)),For a particular product,verification does not end
until,in accordance with Sec,417.5(c),the establishment has reviewed
the records associated with its production,
Paragraph (c) of Sec,417.5 provides that,
Prior to shipping product,the establishment shall review the
records associated with the production of that product,documented
in accordance with this section,to ensure completeness,including
the determination that all critical limits were met and,if
appropriate,corrective actions were taken,including the proper
disposition of product,Where practicable,this review shall be
conducted,dated,and signed by an individual who did not produce
the record(s),preferably by someone trained in accordance with
Sec,417.7 of this part,or the responsible establishment official,
As federally inspected establishments prepare to implement HACCP plans
under part 417,the Agency has received inquiries about what actions
establishments must take to comply with this paragraph of the
regulations,In particular,people have asked whether an establishment
can satisfy the requirement for a final,records-based verification by
using any procedure other than one in which a single reviewer looks at
all the records for the product as it is assembled on the shipping dock
and loaded for transportation from the establishment,
FSIS is publishing this notice to provide information to owners and
operators of federally inspected establishments on the types of
procedures that the Agency anticipates will satisfy this requirement,
The essence of Sec,417.5(c) is to require that establishments take
responsibility not only for developing and implementing HACCP plans,
but also for maintaining control of products until they ensure that
60
Guidebook
establishment personnel have applied those plans appropriately and
effectively,FSIS has not prescribed how establishments comply,and it
views the regulations as sufficiently flexible to accommodate records'
review schemes in addition to the procedure described in the previous
paragraph,
Establishment personnel can review production records at any point
after processing and before shipment of the product,including,for
example,at the end of the day of production before a product goes into
on-site storage,while a product is in on-site storage,or during
preparation of shipping documents before assembling product for
transportation from the establishment,Consistent with the regulations,
an establishment also can initiate checks for records' completeness
earlier and accomplish the review in stages,For example,an
establishment that slaughters and bones cattle carcasses one day and
prepares ground beef the next could make one reviewer responsible for
performing slaughter and boning records' review on the first day and
carry the review forward to the second day,when another reviewer
assumes responsibility for the remaining tasks necessary to ensure that
there has been an establishment determination that all critical limits
were met and,if appropriate,corrective actions were taken and that
production records are otherwise complete and then signs and dates the
review,In addition,establishments that maintain records on computers
in accordance with Sec,417.5(d) may be able to accomplish much of the
record checking electronically,
The crucial concern is that there be verification that
establishment controls have ensured proper product disposition,so that
adulterated product is not distributed,FSIS has not,at this point,
ruled out the possibility that a company might operate in compliance
with this regulation despite the fact that the records-based
verification is being conducted when the company transfers a product
from the preparation establishment to another,storage location and
holds the product there,maintaining control of the product,until the
company completes the review and releases the product for shipment to
retail outlets,Industry members interested in instituting a records'
review scheme that includes this type of feature may wish to consult
with the Agency about the types of safeguards needed to ensure that
product is not shipped for distribution until the required verification
is performed,(In Secs,318.309(d)(1)(viii) and 381.309(d)(1)(viii),
the canning and canned products' regulations address a similar
situation as an exception,for which an establishment must obtain area
supervisor approval,to the prohibition against shipping product from
the establishments before the end of the required incubation period.)
FSIS also notes that establishment compliance with part 417
requirements does not affect the applicability of section 10 of the
FMIA or section 9(a) of the PPIA (21 U.S.C,610 and 458(a)); in
particular,transporting,or offering for transportation,adulterated
livestock products or poultry products is prohibited,
Done at Washington,D.C.,on,February 27,1998,
Thomas J,Billy,
Administrator,
[FR Doc,98-5770 Filed 3-5-98; 8:45 am]
BILLING CODE 3410-DM-P
61
-----------------------------------------------------------------------
Guidebook
HACCP Plan Requirements and Meat and Poultry Product
Processing Categories; Policy Clarification
[Federal Register,April 1,1998 (Volume 63,Number 62)]
[Rules and Regulations]
[Page 15739-15740]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr01ap98-1]
=======================================================================
Rules and Regulations
Federal Register
_______________________________________________________________________
This section of the FEDERAL REGISTER contains regulatory documents
having general applicability and legal effect,most of which are keyed
to and codified in the Code of Federal Regulations,which is published
under 50 titles pursuant to 44 U.S.C,1510,
The Code of Federal Regulations is sold by the Superintendent of Documents,
Prices of new books are listed in the first FEDERAL REGISTER issue of each
week,
=======================================================================
[[Page 15739]]
=======================================================================
DEPARTMENT OF AGRICULTURE
Food Safety and Inspection Service
9 CFR Part 417
[Docket No,98-006N]
HACCP Plan Requirements and Meat and Poultry Product Processing
Categories; Policy Clarification
AGENCY,Food Safety and Inspection Service,
ACTION,Policy clarification,
SUMMARY,The Food Safety and Inspection Service (FSIS) is publishing
this document to clarify its policy in regard to HACCP (Hazard Analysis
and Critical Control Points) requirements for meat and poultry
62
Guidebook
establishments producing either multiple products that fall within a
single processing category or single products that pass through
multiple processing categories,
DATES,Comments must be received on or before June 1,1998,
ADDRESSES,Submit one original and two copies of written comments to
FSIS Docket Clerk,Docket #98-006N,U.S,Department of Agriculture,
Food Safety and Inspection Service,Room 102,Cotton Annex,300 12 St.,
SW,Washington,DC 20250-3700,All comments submitted in response to
this document will be available for public inspection in the Docket
Clerk's Office between 8:30 a.m,and 4:30 p.m.,Monday through Friday,
FOR FURTHER INFORMATION CONTACT,
Patricia F,Stolfa,Assistant Deputy Administrator,Regulations and
Inspection Methods,Food Safety and Inspection Service,U.S,Department
of Agriculture (202) 205-0699,
SUPPLEMENTARY INFORMATION,
Background
On July 25,1996,FSIS published a final rule establishing new
requirements intended to improve the safety of meat and poultry
products and facilitate the modernization of USDA's meat and poultry
inspection system (“Pathogen Reduction; Hazard Analysis and Critical
Control Point (HACCP) Systems”; 61 FR 38806),The final rule requires
all official meat and poultry establishments to implement HACCP,a
science-based process control system,Under the new regulations,all
official establishments are responsible for developing and implementing
HACCP plans incorporating the controls necessary and appropriate to
ensure that their meat or poultry products are safe,
HACCP is a flexible system that enables establishments to develop
and implement control systems customized to the nature and volume of
their production,Accordingly,FSIS has promulgated regulatory
requirements meant to provide meat and poultry establishments with the
maximum flexibility for developing and implementing HACCP plans,FSIS
is publishing this notice to clarify the regulatory requirements for
establishments that wish to develop and implement a single HACCP plan
for multiple,similar products or for a single product that passes
through multiple processing categories,
Under Sec,417.2,paragraph (a) of the HACCP requirements,FSIS
requires meat and poultry establishments to conduct a hazard analysis
to determine what food safety hazards are reasonably likely to occur in
the production process and identify the preventive measures it can
apply to control those hazards,Whenever a hazard analysis reveals that
one or more food safety hazards are reasonably likely to occur,FSIS
requires that each establishment develop and implement a written HACCP
plan covering each product produced by that establishment,Further,
FSIS specifically requires that establishments develop HACCP plans for
products that fall into the following processing categories,
(i) Slaughter--all species,
(ii) Raw product--ground,
(iii) Raw product--not ground,
(iv) Thermally processed--commercially sterile,
(v) Not heat treated--shelf stable,
63
Guidebook
(vi) Heat treated--shelf stable,
(vii) Fully cooked--not shelf stable,
(viii) Heat treated but not fully cooked--not shelf stable,
(ix) Product with secondary inhibitors--not shelf stable,
Section 417.2(b)(2) states,A single HACCP plan may encompass
multiple products within a single processing category identified in
this paragraph,if the food safety hazards,critical control points
(CCP's),critical limits,and procedures required to be identified and
performed * * * are essentially the same,provided that any required
features of the plan that are unique to a specific product are clearly
delineated in the plan and are observed in practice.” Many meat and
poultry establishments,especially processing establishments,
manufacture numerous products that have most of their processing steps
in common,Allowing a single HACCP plan for such products was intended
to simplify and improve both compliance and inspection,
For example,an establishment producing both ready-to-eat corned
beef and ready-to-eat roast beef could develop and implement a single
HACCP plan for both products,The HACCP plan would identify the common
CCP's and critical limits (cooking and cooling product in accordance
with time/temperature combinations predetermined by the establishment),
as well as any processing differences (the corned beef would undergo a
curing step),In this example,compliance with HACCP requirements is
simplified,and it is probably more efficient and cost-effective to
develop and implement a single HACCP plan for the two products than to
produce two separate plans,Inspection is also improved and simplified
because FSIS inspection personnel can more efficiently and effectively
review a single,unified HACCP plan,
In this document,FSIS also is clarifying that meat and poultry
establishments may develop a single HACCP plan for a single product
that passes through multiple processing categories,It is likely that
such HACCP plans would be developed and implemented,for the most part,
by establishments that both slaughter (category (i)) and process
(categories (ii) through (ix)) meat or poultry,For example,there are
numerous establishments that slaughter,grind,and package meat for
retail sale,There also are numerous establishments that slaughter,cut
up,and package poultry for retail sale,Many of these and similar
establishments probably will choose to develop and implement a single
HACCP
[[Page 15740]]
plan covering both slaughter and processing,Developing and
implementing a single HACCP plan for a single product often would be
more efficient and cost effective than producing two plans (one for
slaughter and one for processing),In many cases,FSIS inspection
personnel will be able to more efficiently and effectively review a
single HACCP plan that covers all of the processing (including
slaughter) within a meat or poultry establishment,
Done in Washington,DC,March 18,1998,
Thomas J,Billy,
Administrator,Food Safety Inspection Service,
[FR Doc,98-8432 Filed 3-31-98; 8:45 am]
BILLING CODE 3410-DM-P
64
-----------------------------------------------------------------------
-----------------------------------------------------------------------
Guidebook
Listeria Monocytogenes Contamination of Ready-to-Eat Products
[Federal Register,May 26,1999 (Volume 64,Number 101)]
[Rules and Regulations]
[Page 28351-28353]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr26my99-2]
DEPARTMENT OF AGRICULTURE
Food Safety and Inspection Service
9 CFR Parts 416 and 417
[Docket No,99-025N]
Listeria Monocytogenes Contamination of Ready-to-Eat Products
AGENCY,Food Safety and Inspection Service,USDA,
ACTION,Compliance with the HACCP system regulations and request for
comment,
SUMMARY,The Food Safety and Inspection Service (FSIS) is publishing
this document to inform manufacturers of ready-to-eat livestock and
poultry products of the Agency's views about the application of the
hazard analysis and critical control point (HACCP) system regulations
to contamination with Listeria monocytogenes,
FSIS believes that the findings from testing a range of ready-to-
eat products and information from investigations of outbreaks of
listeriosis constitute changes that could affect an establishment's
hazard analysis or alter the HACCP plan for affected products,
Therefore,establishments must reassess their HACCP plans for ready-to-
eat livestock and poultry products,If reassessment results in a
determination that Listeria monocytogenes contamination is a food
safety hazard reasonably likely to occur in the establishment's
production process,then it is a type of microbiological contamination
that must be addressed in a HACCP plan,
In this document,FSIS is setting out several factors that it
believes an establishment should consider when performing its
reassessment,Also,FSIS is making guidance material available that
establishments may find helpful,(See ADDRESSES),FSIS invites comments
on the factors addressed in this document and on its guidance material,
DATES,Comments may be submitted by July 26,1999,
ADDRESSES,Submit one original and two copies of written comments to
FSIS Docket Clerk,Docket No,99-025N,U.S,Department of Agriculture,
65
Guidebook
Food Safety and Inspection Service,Room 102,Cotton Annex,300 12th
Street,SW,Washington,DC 20250-3700,All comments submitted in
response to this document will be available for public inspection in
the Docket Clerk's office between 8:30 a.m,and 4:30 p.m.,Monday
through Friday,
Guidance material is available from the Inspection Systems
Development Division,FSIS,USDA,Room 202,Cotton Annex Building,300
12th Street SW,Washington,DC 20250-3700,phone (202) 720-3219,Fax
(202) 690-0824,The material is also available on the FSIS Homepage,
http://www.fsis.usda.gov/index.htm
FOR FURTHER INFORMATION CONTACT,Daniel L,Engeljohn,Ph.D.,Director,
Regulations Development and Analysis Division,Food Safety and
Inspection Service,Washington,DC 20250-3700; (202) 720-5627,
SUPPLEMENTARY INFORMATION,
Regulatory Context
The Food Safety and Inspection Service (FSIS) administers the
regulatory program under the Federal Meat Inspection Act (FMIA) (21
U.S.C,601 et seq.) and the Poultry Products Inspection Act (PPIA) (21
U.S.C,451 et seq.) to protect the health and welfare of consumers by
preventing the distribution of livestock and poultry products that are
unwholesome,adulterated,or misbranded,To further the goal of
reducing the risk of foodborne illness from livestock and poultry
products to the maximum extent possible,FSIS issued the Pathogen
Reduction-Hazard Analysis and Critical Control Point (HACCP) Systems
final rule on July 25,1996 (61 FR 38806),These regulations require
federally inspected establishments to take preventive and corrective
measures at each stage of the food production process where food safety
hazards occur,
Part 416,the regulations on Sanitation Standard Operating
Procedures (SOP's),requires establishments to develop,implement,and
maintain written SOP's for sanitation that describe daily procedures
that are sufficient to prevent direct contamination or adulteration of
products (Sec,416.11 and 416.12(a)),Part 417,the regulations on
HACCP systems,requires a hazard analysis to determine the food safety
hazards reasonably likely to occur in the production process and
identify the preventive measures an establishment can apply to control
those hazards in the production of particular products (Sec,417.2(a)),
Whenever a hazard analysis reveals one or more such hazards,the
regulations require the establishment to develop and implement a
written HACCP plan,for each product,that includes specified controls
for each hazard so identified (Sec,417.2(b)(1) and (c)),
When FSIS issued the Pathogen Reduction-HACCP Systems final rule,
it responded to questions about the link between Sanitation SOP's and
HACCP plans by noting the importance of Sanitation SOP's as tools for
meeting existing sanitation responsibilities and preventing direct
product contamination and adulteration and their appropriateness as
near-term procedures--that is,for implementation prior to HACCP
implementation and,in a sense,as a prerequisite to HACCP,In response
to concerns about redundancy,the Agency noted that a sanitation
procedure incorporated into a validated HACCP plan need not be
duplicated in the establishment's Sanitation SOP's,FSIS also
anticipated that some Sanitation SOP procedures,such as those
addressing pre-operational cleaning of facilities,equipment,and
66
Guidebook
utensils were likely to remain in an establishment's Sanitation SOP's,
(61 FR 38834.)
The HACCP system regulations require an official establishment to
develop and implement a written HACCP plan whenever a hazard analysis
reveals one or more food safety hazards that are reasonably likely to
occur in the production process ((Sec,417.2(a),(b)(1),and (c)),
Paragraph (a)(1) of Sec,417.2 specifies the purpose of a hazard
analysis,``to determine the food safety hazards reasonably likely to
occur in the production process and identify the preventive measures
the establishment can apply to control those hazards.'' Ten potential
hazard areas,including microbiological contamination,are listed to
guide establishments in this analysis (Sec,417.2(a)(3)),
Section 417.2(a)(1) also provides that a food safety hazard is
reasonably likely to occur if a prudent establishment would establish
controls because the hazard historically has occurred,or because there
is a reasonable possibility that it will occur in the particular type
of product being processed,in the absence of those controls,
The likelihood that a potential food safety hazard will occur in
the production process for a particular
[[Page 28352]]
product at a given location,and the identification and adequacy of
preventive measures to control a likely hazard,must be determined by
each establishment,Obviously,conditions may well change over time,
For this reason,the HACCP system regulations require every
establishment to reassess HACCP plan adequacy at least annually and
whenever any changes occur that could affect the underlying hazard
analysis or alter the HACCP plan (Sec,417.4(a)(3)),When reassessment
reveals that a plan no longer meets the requirements for the contents
of a HACCP plan,the establishment must modify the plan immediately
(Sec,417.4(a)(3)),
Listeria Monocytogenes
Listeria monocytogenes is a type of pathogenic bacteria often found
in the intestines of healthy animals (including humans) and in the
environments in which food producing animals are raised and processed
(e.g.,in soil,water,and vegetation and on the surfaces of equipment,
floors,and walls),Therefore,food may be contaminated with this
microorganism and,after cooking or other treatment to destroy the
pathogen,may be recontaminated,
Listeria monocytogenes can cause listeriosis,a serious and
sometimes fatal illness,for which pregnant women,newborns,the
elderly,and people with weakened immune systems are at risk,The most
common manifestation of listeriosis is meningitis,It also can cause
miscarriages and stillbirths,Advances in molecular subtyping methods
have improved scientists' ability to associate Listeria monocytogenes
with particular products and to detect outbreaks of listeriosis,
Since the late 1980's,FSIS and the Food and Drug Administration
(FDA) have worked with food manufacturers to improve procedures for
ensuring that ready-to-eat foods (i.e.,products that may be consumed
without any further cooking or other preparation) are free of Listeria
monocytogenes,In addition,for the past decade,FSIS has conducted a
microbiological testing program in which the Agency samples ready-to-
eat livestock and poultry products,including cooked and fermented
sausages,cooked corned beef,sliced ham and luncheon meats,beef
67
Guidebook
jerky,cooked uncured poultry,and salads and spreads,in federally
inspected establishments,(For the Agency's current testing program
instructions,see FSIS Directive 10,240.2,Microbial Sampling of Ready-
to-Eat Products Produced by Establishments Operating Under a HACCP
System.) FSIS treats ready-to-eat products in which Listeria
monocytogenes is found as adulterated under the FMIA or the PPIA (21
U.S.C,453(g) or 601(m)),
Between 1989 and 1993,the rate of illness from Listeria
monocytogenes declined,Over the next several years,there did not
appear to be any further decline,however,and since last fall,there
has been an increase in the number of cases caused by a specific
subtype--a previously rare ``E'' pattern--of Listeria monocytogenes,
The Centers for Disease Control,U.S,Public Health Service,Department
of Health and Human Services (DHHS),have reported 101 illnesses,15
adult deaths and 6 stillbirths or miscarriages associated with this
``E'' pattern,Using methodological advances that provide more specific
information about pathogens isolated from foods and humans,public
health agencies have obtained information associating the ``E'' pattern
subtype of Listeria monocytogenes with livestock and poultry products,
FSIS currently is evaluating a range of measures,both short- and
long-term,to improve public health protection against this pathogen,
In aid of this evaluation,FSIS held a public meeting on February 10,
1999,at which research,regulation,and education activities along
with industry and government procedures,were discussed,
Controlling Listeria Monocytogenes Contamination
FSIS is publishing this document to advise federally inspected
establishments of the Agency's current position on one aspect of the
public health strategy to deal with Listeria monocytogenes
contamination and to provide an opportunity to comment on that position
as FSIS continues to develop a comprehensive strategy,FSIS is
concerned because some establishments have not reassessed their HACCP
plans after recent outbreaks of listeriosis caused by contaminated
ready-to-eat livestock and poultry products,and after some
establishments have produced ready-to-eat products adulterated with
Listeria monocytogenes,If Listeria monocytogenes contamination is a
food safety hazard reasonably likely to occur in an establishment's
production process,then it must be addressed in a HACCP plan,It would
not be sufficient to claim that the hazard is adequately dealt with in
the establishment's Sanitation SOP,HACCP plan reassessment is
necessary to determine whether the plan appropriately addresses this
hazard,
FSIS views investigations of recent outbreaks of listeriosis and
findings of Listeria monocytogenes contamination,along with other
information now available on the prevalence and persistence of this
foodborne pathogen,as sufficient evidence that some establishments'
present approach to the food safety hazard presented by ready-to-eat
livestock food and poultry products adulterated with Listeria
monocytogenes does not comply with part 417 requirements,Therefore,
FSIS believes that Sec,417.4(a)(3) requires that establishments
reassess the HACCP plans that cover ready-to-eat livestock and poultry
products,
Put another way,the Agency does not see how--given the current
record of contamination incidents and information now available on the
prevalence and persistence of the microorganism,its ability to survive
under adverse conditions,and the apparent susceptibility of some
68
Guidebook
products to contamination--an establishment that produces a ready-to-
eat product (other than one that is thermally processed-commercially
sterile,in accordance with part 318,subpart G,or part 381,subpart
X,of the regulations) could have confidence that,in operation,the
HACCP plan for the product meets part 417 requirements,
FSIS' conclusion addresses only the need for HACCP plan
reassessment,FSIS cannot predict the likelihood that an establishment
producing ready-to-eat products would be required under the regulations
to incorporate,or alter,controls to prevent Listeria monocytogenes
contamination in one or more HACCP plans as a result of plan
reassessment,FSIS does believe,however,that given current knowledge,
Listeria monocytogenes contamination should be considered to be
reasonably likely to occur in the production of ready-to-eat livestock
and poultry products,especially if an establishment has produced
products adulterated with Listeria monocytogenes,or if the
establishment is producing one or more ready-to-eat products that are
susceptible to Listeria monocytogenes contamination in an environment
that is not known to be free of this pathogen,
FSIS urges establishments that produce ready-to-eat livestock and
poultry products to perform the reassessment of their HACCP plans
within 30 days of the publication of this document,FSIS will instruct
its inspection personnel to verify that reassessments were conducted,
If an establishment does not reassess its HACCP plan in accord with
this document,FSIS will evaluate the establishment's compliance with
Part 417,
[[Page 28353]]
Set out below are factors that FSIS believes are relevant in
determining whether Listeria monocytogenes contamination is a food
safety hazard reasonably likely to occur in the production process and
in identifying preventive measures that establishments can apply to
control the hazard,Reassessments of HACCP plans should take these
factors into account,FSIS is providing technical information and other
Agency guidance material,(See ADDRESSES to obtain copies.) The Agency
invites comments on this guidance material and the factors set out
below,
(1) Pathogen Levels in Starting Materials FSIS believes that it is
crucial that each establishment know the characteristics of its
starting materials and,in particular,keep itself informed about
evidence of Listeria monocytogenes contamination of the raw materials
or source of raw materials that the establishments use,
(2) Validation of Lethality Treatment FSIS believes industry
members must comply rigorously with the HACCP plan validation
requirements of Sec,417.4(a)(1),especially in ensuring that the
establishment can successfully apply a scientifically appropriate
lethality treatment under its commercial operating conditions (see 61
FR 38826-38827),Until the establishment demonstrates that it achieves
the anticipated lethality effect under actual in-plant conditions,
effectiveness is theoretical,and the plan is not validated,
(3) Exposure to Contamination After Lethality Treatment The
available evidence on the presence of Listeria monocytogenes in food
processing environments appears to indicate an increased potential for
the contamination of product after a food is processed to destroy
pathogenic microorganisms,Therefore,an establishment's reassessment
of its HACCP plans needs to address such potential contamination,
Establishments should account for finished product characteristics such
69
Guidebook
as water activity,pH,and the presence or absence of one or more
barriers that inhibit pathogen growth,The HACCP plan must incorporate
any hazards identified by the reassessment,
(4) Evidence of Product Contamination FSIS believes that any
finding of Listeria monocytogenes in an establishment's ready-to-eat
product,whether in government or industry test results,is
substantial,and perhaps conclusive,evidence that Listeria
monocytogenes contamination is a food safety hazard that is reasonably
likely to occur in its production process for that product,Therefore,
in the event of such a finding,FSIS' position is as follows,If the
establishment's HACCP plan does not already provide for the control of
Listeria monocytogenes,and absent substantial,scientifically
supportable reasons,that HACCP plan must be modified to address the
Listeria monocytogenes hazard and incorporate appropriate controls,If
the establishment's HACCP plan does address and control for Listeria
monocytogenes,the establishment must take the appropriate corrective
actions in accord with the requirements of 9 CFR 417.3,FSIS inspection
personnel will verify that the establishment has taken the necessary
corrective actions,
Done at Washington,D.C.,on May 19,1999,
Thomas J,Billy,
Administrator,
[FR Doc,99-13223 Filed 5-25-99; 8:45 am]
BILLING CODE 3410-DM-P
70