? E,F,Schubert,Rensselaer Polytechnic Institute,2003
1
Bipolar junction transistor - History
Basic operation of BJT
(1) Hole particle current from E to B
(2) Electron particle current from B to E
(3) Recombination current in B
(4) Hole particle current originating in E and reaching C
(5) Reverse electron particle current from C to B
(6) Reverse hole particle current from B to C
(What is difference between,current” and,particle current”?)
E,F,Schubert,Rensselaer Polytechnic Institute,2003
2
Qualitative basic operation of BJTs
What is a BJT?
A BJT consists of two back-to-back p-n junctions,
The middle region,the base,is very thin,
The three regions are the emitter,base,and collector,
Carriers are injected (“emitted”) into the base from the emitter,
Since the base is thin,most carriers injected into base diffuse into
collector,
What does a,thin base thickness” mean? ? Base thickness is much
thinner than the diffusion length of carriers injected from the emitter,
E,F,Schubert,Rensselaer Polytechnic Institute,2003
3
History of point-contact transistor
The first transistor was a point-contact transistor
E,F,Schubert,Rensselaer Polytechnic Institute,2003
4
Model of transistor in Bell Labs museum
Museum is located at 600 Mountain Ave.,Murray Hill,New Jersey
E,F,Schubert,Rensselaer Polytechnic Institute,2003
5
History of the first transistor
,The first transistor was about half an inch high,Before Brattain started,
John Bardeen told him that they would need two metal contacts within
0.002 inches (0.002 inches = 50 μm) of each other - about the thickness
of a sheet of paper,But the finest wires then were almost three times
that width and couldn’t provide the kind of precision they needed,Instead
of bothering with tiny wires,Brattain attached a single strip of gold foil
over the point of a plastic triangle,With a razor blade,he sliced through
the gold right at the tip of the triangle,Voila,two gold contacts just a hair-
width apart,
The whole triangle was then held over a crystal of germanium on a
spring,so that the contacts lightly touched the surface,The germanium
itself sat on a metal plate attached to a voltage source,This contraption
was the very first semiconductor amplifier,because when a bit of current
came through one of the gold contacts,another even stronger current
came out the other contact,
E,F,Schubert,Rensselaer Polytechnic Institute,2003
6
Here’s why it worked,Germanium is a semiconductor and,if properly
treated,can either let lots of current through or let none through,This
germanium had an excess of electrons,but when an electric signal
traveled in through the gold foil,it injected holes (the opposite of
electrons) into the surface,This created a thin layer along the top of the
germanium with too few electrons,
Semiconductors with too many electrons are known as N-type and
semiconductors with too few electrons are known as P-type,The
boundary between these two kinds of semiconductors is known as a P-N
junction,and it’s a crucial part of a transistor,In the presence of this
junction,current can start to flow from one side to the other,In the case
of Brattain’s transistor,current flowed towards the second gold contact,
Think about what that means,A small current in through one contact
changes the nature of the semiconductor so that a larger,separate
current starts flowing across the germanium and out the second contact,
A little current can alter the flow of a much bigger one,effectively
amplifying it,Of course,a transistor in a telephone or in a radio has to
handle complex signals,The output contact can’t just amplify a steady
E,F,Schubert,Rensselaer Polytechnic Institute,2003
7
hum of current,it has to dutifully replicate a person’s voice,or an entire
symphony,Luckily,a semiconductor is perfectly suited to this job,It is
exquisitely sensitive to how many extra or missing electrons are inside,
Each time the input signal shoves more holes into the germanium,it
changes the way current flows across the crystal - the output current
instantly gets larger and smaller,perfectly mimicking the input.”
(after Public Broadcasting System (PBS) television series,1999)
E,F,Schubert,Rensselaer Polytechnic Institute,2003
8
How did first point-contact transistor work?
E,F,Schubert,Rensselaer Polytechnic Institute,2003
9
A gold foil was glued to a triangular insulating wedge,
A narrow gap was cut with a razor blade to form the E and C,
The gap was approximately 50 μm wide,
Under forward bias of the EB junction,minority carriers are injected into
base (In case of point-contact transistor,strong forward bias is required),
How are minority carriers injected without a p-n junction?
Most minority carriers are collected by the reverse-biased BC junction,
Thus the base controls the current flow between E and C,
E,F,Schubert,Rensselaer Polytechnic Institute,2003
10
How are minority carriers injected without a p-n junction?
Answer,
… strong forward-bias is needed for minority carrier injection,
Can Schottky contacts emit light? If yes,under which circumstances?
Are there other circumstances under which Schottky contacts emit light?
E,F,Schubert,Rensselaer Polytechnic Institute,2003
11
Problems of the point-contact transistor,
The point-contact transistor is a surface-effect device,i,e,important
effects occur at the semiconductor surface,
Surfaces are easily contaminated,
Surface-effect devices are unstable (e,g,mechanical vibrations),
Remedy,
William Shockley invented the pn-junction transistor,
The physically relevant region is moved to the bulk of the material,
The p-n junction transistor is a bulk device,
Shockley,Bardeen,and Brattain were awarded the Nobel Prize in 1956,
E,F,Schubert,Rensselaer Polytechnic Institute,2003
12
History of BJTs
E,F,Schubert,Rensselaer Polytechnic Institute,2003
13
Questions
Why is the E called E?
Why is the C called C?
Why is the B called B?
What is meant by,thin” in context of,thin base thickness”?
The EB junction is forward biased,Many more carriers flow from E ? B
than from B ? E,Why is it supposed to be that way? How is this
achieved?
What are differences between point-contact transistor and junction
transistor?
Which of these two transistors is no longer used and why?
E,F,Schubert,Rensselaer Polytechnic Institute,2003
14
References
Historical materials are courtesy of AT&T Bell Laboratories
B,G,Streetman and S,Banerjee "Solid State Electronic Devices"
(Prentice Hall,Englewood Cliffs NJ,1999)
PBS television series on transistor (1999)
1
Bipolar junction transistor - History
Basic operation of BJT
(1) Hole particle current from E to B
(2) Electron particle current from B to E
(3) Recombination current in B
(4) Hole particle current originating in E and reaching C
(5) Reverse electron particle current from C to B
(6) Reverse hole particle current from B to C
(What is difference between,current” and,particle current”?)
E,F,Schubert,Rensselaer Polytechnic Institute,2003
2
Qualitative basic operation of BJTs
What is a BJT?
A BJT consists of two back-to-back p-n junctions,
The middle region,the base,is very thin,
The three regions are the emitter,base,and collector,
Carriers are injected (“emitted”) into the base from the emitter,
Since the base is thin,most carriers injected into base diffuse into
collector,
What does a,thin base thickness” mean? ? Base thickness is much
thinner than the diffusion length of carriers injected from the emitter,
E,F,Schubert,Rensselaer Polytechnic Institute,2003
3
History of point-contact transistor
The first transistor was a point-contact transistor
E,F,Schubert,Rensselaer Polytechnic Institute,2003
4
Model of transistor in Bell Labs museum
Museum is located at 600 Mountain Ave.,Murray Hill,New Jersey
E,F,Schubert,Rensselaer Polytechnic Institute,2003
5
History of the first transistor
,The first transistor was about half an inch high,Before Brattain started,
John Bardeen told him that they would need two metal contacts within
0.002 inches (0.002 inches = 50 μm) of each other - about the thickness
of a sheet of paper,But the finest wires then were almost three times
that width and couldn’t provide the kind of precision they needed,Instead
of bothering with tiny wires,Brattain attached a single strip of gold foil
over the point of a plastic triangle,With a razor blade,he sliced through
the gold right at the tip of the triangle,Voila,two gold contacts just a hair-
width apart,
The whole triangle was then held over a crystal of germanium on a
spring,so that the contacts lightly touched the surface,The germanium
itself sat on a metal plate attached to a voltage source,This contraption
was the very first semiconductor amplifier,because when a bit of current
came through one of the gold contacts,another even stronger current
came out the other contact,
E,F,Schubert,Rensselaer Polytechnic Institute,2003
6
Here’s why it worked,Germanium is a semiconductor and,if properly
treated,can either let lots of current through or let none through,This
germanium had an excess of electrons,but when an electric signal
traveled in through the gold foil,it injected holes (the opposite of
electrons) into the surface,This created a thin layer along the top of the
germanium with too few electrons,
Semiconductors with too many electrons are known as N-type and
semiconductors with too few electrons are known as P-type,The
boundary between these two kinds of semiconductors is known as a P-N
junction,and it’s a crucial part of a transistor,In the presence of this
junction,current can start to flow from one side to the other,In the case
of Brattain’s transistor,current flowed towards the second gold contact,
Think about what that means,A small current in through one contact
changes the nature of the semiconductor so that a larger,separate
current starts flowing across the germanium and out the second contact,
A little current can alter the flow of a much bigger one,effectively
amplifying it,Of course,a transistor in a telephone or in a radio has to
handle complex signals,The output contact can’t just amplify a steady
E,F,Schubert,Rensselaer Polytechnic Institute,2003
7
hum of current,it has to dutifully replicate a person’s voice,or an entire
symphony,Luckily,a semiconductor is perfectly suited to this job,It is
exquisitely sensitive to how many extra or missing electrons are inside,
Each time the input signal shoves more holes into the germanium,it
changes the way current flows across the crystal - the output current
instantly gets larger and smaller,perfectly mimicking the input.”
(after Public Broadcasting System (PBS) television series,1999)
E,F,Schubert,Rensselaer Polytechnic Institute,2003
8
How did first point-contact transistor work?
E,F,Schubert,Rensselaer Polytechnic Institute,2003
9
A gold foil was glued to a triangular insulating wedge,
A narrow gap was cut with a razor blade to form the E and C,
The gap was approximately 50 μm wide,
Under forward bias of the EB junction,minority carriers are injected into
base (In case of point-contact transistor,strong forward bias is required),
How are minority carriers injected without a p-n junction?
Most minority carriers are collected by the reverse-biased BC junction,
Thus the base controls the current flow between E and C,
E,F,Schubert,Rensselaer Polytechnic Institute,2003
10
How are minority carriers injected without a p-n junction?
Answer,
… strong forward-bias is needed for minority carrier injection,
Can Schottky contacts emit light? If yes,under which circumstances?
Are there other circumstances under which Schottky contacts emit light?
E,F,Schubert,Rensselaer Polytechnic Institute,2003
11
Problems of the point-contact transistor,
The point-contact transistor is a surface-effect device,i,e,important
effects occur at the semiconductor surface,
Surfaces are easily contaminated,
Surface-effect devices are unstable (e,g,mechanical vibrations),
Remedy,
William Shockley invented the pn-junction transistor,
The physically relevant region is moved to the bulk of the material,
The p-n junction transistor is a bulk device,
Shockley,Bardeen,and Brattain were awarded the Nobel Prize in 1956,
E,F,Schubert,Rensselaer Polytechnic Institute,2003
12
History of BJTs
E,F,Schubert,Rensselaer Polytechnic Institute,2003
13
Questions
Why is the E called E?
Why is the C called C?
Why is the B called B?
What is meant by,thin” in context of,thin base thickness”?
The EB junction is forward biased,Many more carriers flow from E ? B
than from B ? E,Why is it supposed to be that way? How is this
achieved?
What are differences between point-contact transistor and junction
transistor?
Which of these two transistors is no longer used and why?
E,F,Schubert,Rensselaer Polytechnic Institute,2003
14
References
Historical materials are courtesy of AT&T Bell Laboratories
B,G,Streetman and S,Banerjee "Solid State Electronic Devices"
(Prentice Hall,Englewood Cliffs NJ,1999)
PBS television series on transistor (1999)
