? White Paper SDR SDRAM Controller Introduction The single data rate (SDR) synchronous dynamic random access memory (SDRAM) controller provides a simplified interface to industry standard SDR SDRAM. The SDR SDRAM Controller is available in either Verilog HDL or VHDL and is optimized for the Altera ? APEX ? architecture. The SDR SDRAM Controller supports the following features: ■ Burst lengths of 1, 2, 4, or 8 data words ■ CAS latency of 2 or 3 clock cycles ■ 16-bit programmable refresh counter used for automatic refresh ■ 2-chip selects for SDRAM devices ■ Supports the NOP, READA, WRITEA, AUTO_REFRESH, PRECHARGE, ACTIVATE, BURST_STOP, and LOAD_MR commands ■ Support for full-page mode operation ■ Data mask line for write operations ■ PLL to increase system performance ■ Support for data-path widths of 16, 32, and 64 bits Figure 1 shows a system-level diagram of the SDR SDRAM Controller. Figure 1. SDR SDRAM Controller System-Level Diagram SDRAM Overview SDRAM is high-speed dynamic random access memory (DRAM) with a synchronous interface. The synchronous interface and fully-pipelined internal architecture of SDRAM allows extremely fast data rates if used efficiently. Internally, SDRAM devices are organized in banks of memory, which are addressed by row and column. The number of row- and column-address bits and the number of banks depends on the size of the memory. SDR SDRAM Controller SDR SDRAM CLK SA CS_N BA CKE DQ CAS_N WE_N DQM RAS_N CLK CMD[1:0] CMDACK ADDR DATAIN DM DATAOUT August 2002, ver. 1.1 1 M-WP-SDR-1.1 Altera Corporation SDR SDRAM Controller White Paper SDRAM is controlled by bus commands that are formed using combinations of the RASN, CASN, and WEN signals. For instance, on a clock cycle where all three signals are high, the associated command is a no operation (NOP). A NOP is also indicated when the chip select is not asserted. Table 1 shows the standard SDRAM bus commands. SDRAM banks must be opened before a range of addresses can be written to or read from. The row and bank to be opened are registered coincident with the ACT command. When a bank is accessed for a read or a write it may be necessary to close the bank and re-open it if the row to be accessed is different than the row that is currently opened. Closing a bank is done with the PCH command. The primary commands used to access SDRAM are RD and WR. When the WR command is issued, the initial col- umn address and data word is registered. When a RD command is issued, the initial address is registered. The initial data appears on the data bus 1 to 3 clock cycles later. This is known as CAS latency and is due to the time required to physically read the internal DRAM core and register the data on the bus. The CAS latency depends on the speed of the SDRAM and the frequency of the memory clock. In general, the faster the clock, the more cycles of CAS latency are required. After the initial RD or WR command, sequential read and writes continue until the burst length is reached or a BT command is issued. SDRAM memory devices support burst lengths of 1, 2, 4, or 8 data cycles. The ARF is issued periodically to ensure data retention. This function is performed by the SDR SDRAM Controller and is transparent to the user. The LMR is used to configure the SDRAM mode register. which stores the CAS latency, burst length, burst type, and write burst mode. Consult the SDRAM specification for additional details. SDRAM comes in dual in-line memory modules (DIMMs), small-outline DIMMs (SO-DIMMs) and chips. To reduce pin count SDRAM row and column addresses are multiplexed on the same pins. SDRAM often includes more than one bank of memory internally and DIMMS may require multiple chip selects. Table 1. SDRAM Bus Commands Command Abbreviation RASN CASN WEN No operation NOP H H H Active ACT L H H Read RD H L H Write WR H L L Burst terminate BT H H L Precharge PCH L H L Autorefresh ARF L L H Load mode register LMR L L L 2 Altera Corporation SDR SDRAM Controller White Paper Functional Description Table 2 shows the SDR SDRAM Controller interface signals. All signals are synchronous to the system clock and outputs are registered at the SDR SDRAM Controller’s outputs. Table 2. Interface Signals Signal Name Active I/O Description CLK Clock NA Input System clock. RESET_N Reset Low Input System reset. ADDR[ASIZE-1:0] Memory address NA Input Memory address for read/write requests. Width is set by ASIZE. CMD[2:0] Command NA Input Command request. CMDACK Command acknowledge High Output Acknowledgment of the requested command. DATAIN[DSIZE-1:0] Input data NA Input Input data bus. Width is set by DSIZE. DATAOUT[DSIZE-1:0] Output data NA Output Output data bus. Width is set by DSIZE. DM[(DSIZE/8)-1:0] Data mask High Input Masks individual bytes during data write SA[11:0] Address bus NA Output SA[11:0] are sampled during the ACT command to latch the row address. SA[n:0] are sampled during the RD/WR command to latch the column address where n depends on the size of SDRAM used. SA[10] is sampled during the PCH command to determine if all banks are to be pre- charged or the bank selected by BA[1:0]. The address out- puts also provide the op-code during the LMR command. BA[1:0] Bank address NA Output These signals determine to which bank the ACT, RD, WR, or PCH command is applied. CS_N[1:0] Chip selects Low Output SDRAM chip selects. CKE Clock enable High Output SDRAM CKE input. RAS_N Row address strobe Low Output SDRAM command input. CAS_N Column address strobe Low Output SDRAM command input. WE_N Write enable Low Output SDRAM command input. DQ[DSIZE-1:0] Data bus NA I/O SDRAM data bus. DQM[(DSIZE/8)-1:0] Data mask High Output SDRAM data masks, mask individual bytes during data write. 3 Altera Corporation SDR SDRAM Controller White Paper SDRAM Controller Command Interface The SDR SDRAM Controller provides a synchronous command interface to the SDRAM and several control regis- ters. Table 3 shows the commands, which are described in following sections. The following rules apply to the com- mands: ■ All commands, except NOP, are driven by the user onto CMD[2:0]; ADDR and DATAIN are set appropri- ately for the requested command. The controller registers the command on the next rising clock edge ■ To acknowledge the command the controller asserts CMDACK for one clock period ■ For READA or WRITEA commands, the user should start receiving or writing data on DATAOUT and DATAIN ■ The user must drive NOP onto CMD[2:0]by the next rising clock edge after CMDACK is asserted NOP Command NOP is a no operation command to the controller. When NOP is detected by the controller, it performs a NOP in the following clock cycle. A NOP must be issued the following clock cycle after the controller has acknowledged a com- mand. The NOP command has no affect on SDRAM accesses that are already in progress. READA Command The READA command instructs the SDR SDRAM Controller to perform a burst read with auto-precharge to the SDRAM at the memory address specified by ADDR. The SDR SDRAM Controller issues an ACTIVATE command to the SDRAM followed by a READA command. The read burst data first appears on DATAOUT (RCD + CL + 2) after the SDR SDRAM Controller asserts CMDACK. During a READA command the user must keep DM low. When the controller is configured for full-page mode, the READA command becomes READ (READ without auto-pre- charge). Figure 2 shows an example timing diagram for a READA command. The following sequence describes the general operation of the READA command: ■ The user asserts READA, ADDR and DM ■ The SDR SDRAM Controller asserts CMDACK to acknowledge the command and simultaneously starts issu- ing commands to the SDRAM devices ■ One clock after CMDACK is asserted, the user must assert NOP ■ The CMDACK presents the first read burst value on DATAOUT, the remainder of the read bursts follow every clock cycle Table 3. Interface Commands Command Value Description NOP 000b No operation. READA 001b SDRAM read with auto precharge. WRITEA 010b SDRAM write with auto precharge. REFRESH 011b SDRAM auto refresh. PRECHARGE 100b SDRAM precharge all banks. LOAD_MODE 101b SDRAM load mode register. LOAD_REG1 110b Load controller configuration register. LOAD_REG2 111b Load controller refresh period register. 4 Altera Corporation SDR SDRAM Controller White Paper Figure 2. READA Timing Diagram WRITEA Command The WRITEA command instructs the SDR SDRAM Controller to perform a burst write with auto-precharge to the SDRAM at the memory address specified by ADDR. The SDR SDRAM Controller will issue an ACTIVATE com- mand to the SDRAM followed by a WRITEA command. The first data value in the burst sequence must be presented with the WRITEA and ADDR address. The host must start clocking data along with the desired DM values into the SDR SDRAM Controller (t RCD – 2) clocks after the SDR SDRAM Controller has acknowledged the WRITEA com- mand. See a SDRAM data sheet for how to use the data mask lines DM/DQM. When the SDR SDRAM Controller is in the full-page mode WRITEA becomes WRITE (write without auto-pre- charge). Figure 3 shows an example timing diagram for a WRITEA command. The following sequence describes the general operation of a WRITEA command: ■ The user asserts WRITEA, ADDR, the first write data value on DATAIN, and the desired data mask value on DM ■ The SDR SDRAM Controller asserts CMDACK to acknowledge the command and simultaneously starts issu- ing commands to the SDRAM devices ■ One clock after CMDACK was asserted, the user asserts NOP on CMD ■ The user clocks data and data mask values into the SDR SDRAM Controller through DATAIN and DM Address 1234.n-6n-5n-4 Row Column CLK CMD CMDACK ADDR DATAOUT DQM RAS_N CAS_N WE_N DQ SA BA CS_N CKE NOPREADA 1 2 ... n-8 n-7 n-6 n-5 n-4 NOP D.C. D.C. = Don't Care D.C. PRECHARGE NOP nn-1n-2n-3 nn-1n-2n-3 5 Altera Corporation SDR SDRAM Controller White Paper Figure 3. WRITEA Timing Diagram REFRESH Command The REFRESH command instructs the SDR SDRAM Controller to perform an ARF command to the SDRAM. The SDR SDRAM Controller acknowledges the REFRESH command with CMDACK. Figure 4 shows an example timing diagram of the REFRESH command. The following sequence describes the general operation of a REFRESH com- mand: ■ The user asserts REFRESH on the CMD input ■ The SDR SDRAM Controller asserts CMDACK to acknowledge the command and simultaneously starts issu- ing commands to the SDRAM devices ■ The user asserts NOP on CMD Address 1234567 Row Column CLK CMD CMDACK ADDR DATAIN DQM RAS_N CAS_N WE_N DQ SA BA CS_N CKE NOPWRITEA 1 2345678 DM D.C. = Don't Care NOP D.C. D.C. D.C. D.C. D.C. D.C. 8 6 Altera Corporation SDR SDRAM Controller White Paper Figure 4. REFRESH Timing Diagram PRECHARGE Command The PRECHARGE command instructs the SDR SDRAM Controller to perform a PCH command to the SDRAM. The SDR SDRAM Controller acknowledges the command with CMDACK. The PCH command is also used to gener- ate a burst stop to the SDRAM. Using PRECHARGE to terminate a burst is only supported in the full-page mode. Note that the SDR SDRAM Controller adds a latency from when the host issues a command to when the SDRAM sees the PRECHARGE command of 4 clocks. If a full-page read burst is to be stopped after 100 cycles, the PRE- CHARGE command must be asserted (4 + CL – 1) clocks before the desired end of the burst (CL – 1 requirement is imposed by the SDRAM devices). So if the CAS latency is 3, the PRECHARGE command must be issued (100 – 3 – 1 – 4) = 92 clocks into the burst. Figure 5 shows an example timing diagram of the PRECHARGE command. The following sequence describes the general operation of a PRECHARGE command: ■ The user asserts PRECHARGE on CMD ■ The SDR SDRAM Controller asserts CMDACK to acknowledge the command and simultaneously starts issu- ing commands to the SDRAM devices ■ The user asserts NOP on CMD CLK CMD CMDACK DQM RAS_N CAS_N WE_N DQ SA BA CS_N CKE NOPREFRESH CLK FREQ = 133 MHz NOP 7 Altera Corporation SDR SDRAM Controller White Paper Figure 5. PRECHARGE Timing Diagram LOAD_MODE Command The LOAD_MODE command instructs the SDR SDRAM Controller to perform a LMR command to the SDRAM. The value that is to be written into the SDRAM mode register must be present on ADDR[11:0] with the LOAD_MODE command. The value on ADDR[11:0] is mapped directly to the SDRAM pins A11-A0 when the SDR SDRAM Controller issues the LMR to the SDRAM. Figure 6 shows an example timing diagram. The following sequence describes the general operation of a LOAD_MODE command: ■ The users asserts LOAD_MODE on CMD ■ The SDR SDRAM Controller asserts CMDACK to acknowledge the command and simultaneously starts issu- ing commands to the SDRAM devices ■ One clock after the SDR SDRAM Controller asserts CMDACK, the users asserts NOP on CMD CLK CMD CMDACK DQM RAS_N CAS_N WE_N DQ SA BA CS_N CKE NOPPRECHARGE CLK FREQ = 133 MHz NOP 8 Altera Corporation SDR SDRAM Controller White Paper Figure 6. LOAD_MODE Timing Diagram LOAD_REG1 Command The LOAD_REG1 command instructs the SDR SDRAM Controller to load the internal configuration register REG1. The value that is to be written into REG1 must be presented on the ADDR input simultaneously with the assertion of the command LOAD_REG1. Table 4 shows the bit assignments for REG1. CL is the CAS latency of the SDRAM memory in clock periods and is dependent on the memory device speed grade and clock frequency. Consult the SDRAM data sheet for appropriate settings. CL must be set to the same value as CL for the SDRAM memory devices. RCD is the RAS to CAS delay in clock periods and is dependent on the SDRAM speed grade and clock frequency. RCD = INT(t RCD /clock_period), where t RCD is the value from the SDRAM data sheet and clock_period is the clock period of the SDR SDRAM Controller and SDRAM clock. Table 4. REG1 Bit Definitions Label ADDR Bits Description CL [1:0] CAS latency setting. RCD [3:2] RAS to CAS delay in number of clocks. RRD [7:4] REFRESH command duration in clocks. PM [8] SDR SDRAM Controller mode, 0 = normal 1 = page mode. BL [12:9] Burst length, valid values are 1, 2, 4, 8. CLK CMD CMDACK DQM RAS_N CAS_N WE_N DQ SA BA CS_N ADDR NOPLOAD_MODE CLK FREQ = 133 MHz NOP MODE VALUE 9 Altera Corporation SDR SDRAM Controller White Paper RRD is the refresh to RAS delay in clock periods. RRD is dependent on the SDRAM speed grade and clock fre- quency. RRD= INT(tRRD/clock_period), where tRRD is the value from the SDRAM data sheet and clock_period is the clock period of the SDR SDRAM controller and SDRAM clock. PM is the page mode bit. If PM = 0, the SDR SDRAM Controller operates in non-page mode. If PM = 1, the SDR SDRAM Controller operates in page-mode. See Section “Full-Page Mode Operation” on page 14 for more informa- tion. BL is the burst length the SDRAM devices have been configured for. LOAD_REG2 Command The LOAD_REG2 command instructs the SDR SDRAM Controller to load the internal configuration register REG2. REG2 is a 16-bit value that represents the period between REFRESH commands that the SDR SDRAM Controller issues. The value is set by the equation int(refresh_period/clock_period). For example, if a SDRAM device connected to the SDR SDRAM Controller has a 64-ms, 4096-cycle refresh require- ment the device must have a REFRESH command issued to it at least every 64 ms/4096 = 15.625 09 μs. If the SDRAM and SDR SDRAM Controller are clocked by a 100 MHz clock, the maximum value of REG2 is 15.625 μs/0.01 μs = 1562d. The value that is to be written into REG2 must be presented on the ADDR input simulta- neously with the assertion of the command LOAD_REG2. SDRAM Device Initialization and SDR SDRAM Controller Configuration The SDRAM devices that are connected to the SDR SDRAM Controller must be initialized before they can be accessed. This initialization process sets the burst length, CAS latency, burst type, and operation mode for the SDRAM devices. After the SDRAM devices are initialized, the SDR SDRAM Controller’s configuration registers must be set. To initialize the SDRAM devices and the SDR SDRAM Controller, perform the following steps: ■ Assert the PRECHARGE command (see “PRECHARGE Command” on page 7) ■ Assert a LOAD_MODE command (see “LOAD_MODE Command” on page 8) ■ Assert a LOAD_REG2 command (see “LOAD_REG2 Command” on page 10) ■ Assert a LOAD_REG1 command (see “LOAD_REG1 Command” on page 9) Architecture The SDR SDRAM Controller consists of four main modules: the SDRAM controller, control interface, command, and data path modules. The SDRAM controller module is the top-level module that instantiates the three lower mod- ules and brings the whole design together. The control interface module accepts commands and related memory addresses from the host, decoding the command and passing the request to the command module. The command module accepts commands and addresses from the control interface module, and generates the proper commands to the SDRAM. The data path module handles the data path operations during WRITEA and READA commands. The SDRAM controller module also instantiates a PLL that is used in the CLOCK_LOCK mode to improve I/O timing. This PLL is not essential to the operation of the SDR SDRAM Controller and can be easily removed. Figure 7 shows the SDR SDRAM Controller block diagram. 10 Altera Corporation SDR SDRAM Controller White Paper Figure 7. SDRAM Controller Block Diagram Control Interface Module The control interface module decodes and registers commands from the host, and passes the decoded NOP, WRITEA, READA, REFRESH, PRECHARGE, and LOAD_MODE commands, and ADDR to the command module. The LOAD_REG1 and LOAD_REG2 commands are decoded and used internally to load the REG1 and REG2 registers with values from ADDR. Figure 8 shows the control interface module block diagram. Data Path Refresh Control Command Interface Arbiter Command Generator Request Ack Request Ack CMD[1:0] CMDACK ADDR[ASIZE-1:0] DATAIN[DSIZE-1:0] DM[(DSIZE/8)-1:0] DATAOUT[DSIZE-1:0] SA[11:0] BA[1:0] CS_N[1:0] CKE RAS_N CAS_N WE_N DQ[DSIZE-1:0] DQM[(DSIZE/8)-1:0] Control Interface Module Data Path Module Command Module ADDR OE 11 Altera Corporation SDR SDRAM Controller White Paper Figure 8. Control Interface Module Block Diagram The control interface module also contains a 16-bit down counter and control circuit that is used to generate periodic refresh commands to the command module. The 16-bit down counter is loaded with the value from REG2 and counts down to zero. The REFRESH_REQ output is asserted when the counter reaches zero and remains asserted until the command module acknowledges the request. The acknowledge from the command module causes the down counter to be reloaded with REG2 and the process repeats. REG2 is a 16-bit value that represents the period between REFRESH commands that the SDR SDRAM Controller issues. The value is set by the equation int(refresh_period/clock_period). For example, if an SDRAM device that is connected to the SDR SDRAM Controller has a 64-ms, 4096-cycle refresh requirement, the device must have a REFRESH command issued to it at least every 64 ms/4096 = 15.625 μs. If the SDRAM and SDR SDRAM Controller are clocked by a 100-MHz clock, the maximum value of REG2 is 15.625 μs/0.01μs = 1562d. Command Module The command module accepts decoded commands from the control interface module, refresh requests from the refresh control logic, and generates the appropriate commands to the SDRAM. The module contains a simple arbiter that arbitrates between the commands from the host interface and the refresh requests from the refresh control logic. CMD[2:0] ADDR[ASIZE-1:0] DQ DQ DQ 6 6 NOP READA WRITEA REFRESH PRECHARGE LOAD_MODE LOAD_REG1 LOAD_REG2 DQ DQ en DQ en 12 Refresh Count Load Zero Decode Refresh Control REF_REQ REF_ACK SADDR CLK SC_CL SC_RC SC_RRD SC_PM SC_BL Command Decode ASIZE CMD_ACK DQ CM_ACK 12 The refresh requests from the refresh control logic have priority over the commands from the host interface. If a com- Altera Corporation SDR SDRAM Controller White Paper mand from the host arrives at the same time or during a hidden refresh operation, the arbiter holds off the host by not asserting CMDACK until the hidden refresh operation is complete. If a hidden refresh command is received while a host operation is in progress, the hidden refresh is held off until the host operation is complete. Figure 9 shows the command module block diagram. Figure 9. Command Module Block Diagram After the arbiter has accepted a command from the host, the command is passed onto the command generator portion of the command module. The command module uses three shift registers to generate the appropriate timing between the commands that are issued to the SDRAM. One shift register is used to control the timing the ACTIVATE com- mand; a second is used to control the positioning of the READA or WRITEA commands; a third is used to time com- mand durations, which allows the arbiter to determine if the last requested operation has been completed. The command module also performs the multiplexing of the address to the SDRAM. The row portion of the address is multiplexed out to the SDRAM outputs A[11:0] during the ACTIVATE(RAS) command. The column portion is then multiplexed out to the SDRAM address outputs during a READA(CAS) or WRITEA command. The output signal OE is generated by the command module to control tristate buffers in the last stage of the DATAIN path in the data path module. Data Path Module The data path module provides the SDRAM data interface to the host. Host data is accepted on DATAIN for WRITEA commands and data is provided to the host on DATAOUT during READA commands. Figure 10 shows the data path module block diagram. The DATAIN path consists of a 2-stage pipeline to align data properly relative to the CMDACK and the commands that are issued to the SDRAM. DATAOUT consists of a 2-stage pipeline that registers data from the SDRAM during a READA command. DATAOUT pipeline delay can be reduced to one or even zero reg- isters, with the only affect that the relationship of DATAOUT to CMDACK changes. NOP READA WRITEA REFRESH PRECHARGE LOAD_MODE REF_REQ ADDR[ASIZE-1:0] 4 RAS_N CAS_N WE_N CKE Arbiter CM_ACK do_nop do_reada do_writea do_refresh do_precharge do_load_mode Command Generator REF_ACK DQ 4 DQ 16 16 SA[11:0] BA[1:0] CS_N[1:0] Command Timing SC_CL SC_RC SC_RRD SC_PM SC_BL OE 13 Altera Corporation SDR SDRAM Controller White Paper Figure 10. Data Path Module Block Diagram Full-Page Mode Operation The SDR SRAM Controller supports full-page mode operation of the SDRAM devices that it controls. The SDR SDRAM Controller is configured for full-page operation by setting bit 8 of REG 1 (see section “LOAD_REG1 Com- mand” on page 9). When the SDR SDRAM Controller is in full-page mode, the auto-hidden refresh function is dis- abled and READA and WRITEA commands become READ/WRITE (without auto-precharge). The user interface must handle refreshing the SDRAM devices via the REFRESH command. The user interface must also handle issu- ing appropriate PRECHARGE commands to the SDRAM devices, to close a bank before starting a READ operation to a different row. Figure 11 shows a full-page READ burst with a PRECHARGE to terminate the burst timing dia- gram. The following list details the full-page READ operation: ■ The user asserts the READ Command on CMD and ADDR ■ The SDR SDRAM Controller asserts CMDACK to acknowledge the command and simultaneously starts issu- ing commands to the SDRAM devices ■ One clock after the SDR SDRAM Controller asserts CMDACK, the user asserts NOP on CMD ■ (RCD + CL + 2) clocks after the SDR SDRAM Controller asserted CMDACK, the SDR SDRAM Controller starts clocking the read data out on DATAOUT ■ (CL – 1 + 7) clocks before the last READ data value is to appear on DATAOUT, the user asserts PRE- CHARGE on CMD ■ 4 clocks later, the SDR SDRAM Controller asserts CMDACK to acknowledge the PRECHARGE command and simultaneously issues a PRECHARGE command to the SDRAM devices ■ (CL – 1 + 2) clocks later, the READ burst terminates on DATAOUT DATAIN[DSIZE-1:0] DQ[DSIZE-1:0]DQ DQ DQ DQDATAOUT[DSIZE-1:0] CLK OE 14 Altera Corporation SDR SDRAM Controller White Paper Figure 11. Full-Page READ Burst Timing Diagram Figure 12 shows a full-page WRITE burst with a PRECHARGE to terminate the burst timing diagram. The following list details the full-page WRITE operation is as follows: ■ The user asserts WRITE on CMD and ADDR ■ The SDR SDRAM Controller asserts CMDACK to acknowledge the command and simultaneously starts issu- ing commands to the SDRAM devices ■ One clock after the SDR SDRAM Controller asserts CMDACK, the user asserts NOP on CMD ■ (RCD – 2) clocks after the SDR SDRAM Controller asserts CMDACK, the user starts clocking data into the SDR SDRAM Controller on DATAIN ■ 3 clocks before the last WRITE data value is to appear on DATAOUT, the user asserts PRECHARGE on CMD. This delay is (5 clock command delay – t WR ), which is 2 in this example ■ 4 clocks later, the SDR SDRAM Controller asserts CMDACK to acknowledge the PRECHARGE command and simultaneously issues a PRECHARGE command to the SDRAM devices ■ The full-page WRITE burst is terminated Address 1234.n-6n-5n-4 Row Column CLK CMD CMDACK ADDR DATAOUT DQM RAS_N CAS_N WE_N DQ SA BA CS_N CKE NOPREADA 1 2 ... n-8 n-7 n-6 n-5 n-4 NOP D.C. D.C. = Don't Care D.C. PRECHARGE NOP nn-1n-2n-3 nn-1n-2n-3 15 Altera Corporation SDR SDRAM Controller White Paper Figure 12. Full-Page WRITE Burst Timing Diagram Simulation, Synthesis, Place-&-Route, & Results The SDR SDRAM Controller includes source files, a testbench, synthesis scripts, and support files for place-and- route using the Quartus ? II software version 2.1 targeting an EP20K200EFC672-1X device. Table 5 shows the SDR SDRAM Controller directory structure. Simulation The SDR SDRAM Controller can be simulated by using the behavioral source file sdr_sdram_tb (/simulation direc- tory). The testbench performs the following actions: ■ Instantiates the SDR SDRAM Controller and two SDRAM memory models ■ Configures the SDRAM devices and SDR SDRAM Controller ■ Runs a ramp pattern test using all combinations of CAS latency, burst length, and RAS to CAS delays for a given clock frequency Table 5. SDR SDRAM Controller Directory Structure Directory Description \doc Contains the documentation. \simulation Contains the SDR SDRAM controller testbench. \source Contains the source files for the SDR SDRAM controller. Address 1 2 ... n-4 n-3 n-2 n-1 Row Column CLK CMD CMDACK ADDR DATAIN DQM RAS_N CAS_N WE_N DQ SA BA CS_N CKE NOPWRITE 1 2345.n-2n-1 DM D.C. = Don't Care NOP D.C. D.C. D.C. D.C. D.C. D.C. n PRECHARGE NOP n 16 Altera Corporation SDR SDRAM Controller White Paper Higher clock frequencies (e.g., 133 MHz vs. 100 MHz) limit the RAS to CAS delays and CAS latency choices. The test assumes an interface to a Micron MT481C8M16A2 SDRAM device (not supplied). For more information on the Micron models, see http://www.micron.com. Place & Route The t CO and t SU values are important parameters to consider, if you want to run the SDR SDRAM Controller at higher speeds. In addition Alter a recommends placing data pins in one bank and control pins in another bank. PC133 SDRAM devices typically have a t CO of 5.4 ns and a t SU of 1.5 ns. PCB delay is given by the following equation: PCB delay = (clock (ns)) – (FPGA setup time (ns)) – (SDRAM t CO (ns)) shows typical PCB delays. Figure 13. PCB Delays For a write operation at 133 MHz, the PCB delay = (7.5 – 1.5 – 3.5) = 0.9 ns. For a read operation at 133 MHz, the PCB delay = (7.5 – 1.3 – 5.4) = 1.5 ns. For more information on PCB design for high-speed applications, see Application Note 75: High-Speed Board Designs. Throughput Maximum throughput is achieved with page bursts. For random operation throughput is given by: Throughput = 1/clock period (ns) × data path width (bytes) × burst length of access/number of clock cycles per access For example, if data path width = 32 bits (4 bytes), clock cycles = 20, burst length of access = 8, throughput = 1/7.5 × 4 × 8/20 = 212 Mbytes/s Note, a write throughput is higher than a read throughput, because a WRITEA operation requires 15 clock cycles Performance Table 6 shows the performance results for the SDR SDRAM Controller. The results were generated with the Quartus II software version 2.1 SP1. Table 6. Post Route Performance Comparison Device Internal f MAX (MHz) t CO /t SU (ns/ns) Total LEs APEX 20KE EP20K60EBC356-1X 100 3.3/1.25 219 APEX II EP2A15B724C7 133 3.3/1.3 219 Stratix EP1S10F780C5 133 1.6/1.5 175 Cyclone EP1C6Q240C6 133 1.6/1.4 173 SDRAMFPGA Write Read t = 1.5 ns SU t = 5.4 ns CO t = 1.3 ns CO t = 3.5 ns SU 17 Copyright ? 2002 Altera Corporation. All rights reserved. Altera, The Programmable Solutions Company, the stylized Altera logo, specific device designations, and all other words and logos that are identified as trademarks and/or service marks are, unless noted otherwise, the trademarks and service marks of Altera Corporation in the U.S. and other countries. All other product or service names are the property of their respective holders. Altera products are protected under numerous U.S. and foreign patents and pending applications, maskwork rights, and copyrights. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera Corporation. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. ? 101 Innovation Drive San Jose, CA 95134 (408) 544-7000 http://www.altera.com Altera Corporation SDR SDRAM Controller White Paper 18